Jump to content
SASS Wire Forum

Powder to load 32s with.


Pit Bull Tex

Recommended Posts

Posted

HP 38 or W 231.What else can I use? I can't find either one os these.

Posted

Any chance of finding that?

 

Posted

I will look for all of these.I have some  W 296 that feeds great in the 550.I can't find any data for it for 32s.

 

Posted

Any one  in SASS  sell powder?

 

Posted

I use 16.5 grains of 3 f goex in 32-20 with a 100 grain bullet works good , but have to do some clean up after I shoot  them but  that is not bad .  GOOD LUCK 

Posted

Pit Bull, I can only relate my experience.

I used Trail Boss when I was shooting 38/357 and because I had it, l looked up 32 loads when I decided to go with 32 caliber. 

So far, I have fired  a couple hundred rounds that all worked fine.  

- Trail Boss - 2.2 - 2.5 grains

- RNFP 115gr

- Starline 32 caliber brass

- Federal small pistol primers

YMMV, but this has worked well for me so far. I'm leaning towards the slightly heavier loads (2.5) to get a better chamber seal. 

Good Luck

OO  

Posted

Pit Bull,

you didn't specify WHICH .32, but if its for .32 H&R cases, here are my favorites:

 

Load data listed works great for bullet weights 78 gr up to 100 gr.

1. Clean Shot     3.0 - 3.2 gr    Meters better than any powder I've tried and super consistent in its velocities

2. Red Dot         3.0 - 3.2 gr     another great powder

3. Bullseye        2.8 gr              Best accuracy and probably the cleanest.  

4. Titegroup     2.6 gr             If you close your eyes, TiteGroup is as good as the other 3 in all aspects.

 

I've tested Unique (3.0 gr)  and   Universal  (3.0 gr) with good results, BUT..... not nearly as well as I like the other 4 powders

I listed above.

 

Again, these powders and listed charges worked VERY WELL in bullet weights from 78 to 100 grains, in the

32 H&R case.

 

..........Widder

 

 

 

Posted

Thanks Widder.The problem is just finding any powder.

 

Posted

I use Unique in both .32 H&R mag and .32-20, but I came across an 8# jug of Red Dot not too long back, so with Widder's glowing endorsement, I might have to give it a try.

Posted

Which flavor of 32 are you reloading?

 

What bullet weight? 

 

What powders do you have on hand right now?

Posted

90-100 grain in .32 H&R mag:

Titegroup 2.7 gr

Reddot 3.2 gr

W-231

I like .32s at around 900 fps to get enough recoil so the hammer rolls back to my thumb.

Posted

I’ve been using .32 S&W long brass in my Rugers for about 4 years using the following with very good success. 78 gr coated and lead bullets. Any of these loads have been able to take down shotgun knock down targets as well as plates. They provide good ring on steel for spotters as well.

 

T. B.  1.8 - 2 gr

Win 244   2 - 2.1 gr

Red Dot   2.1 gr

Clays   2.2 gr.

 

 

 

 

Posted
1 hour ago, polecat joe said:

I use 1.9 grs of Clays for a 90 gr bullet

I use 1.9 grs of Clay Dot for 115 gr 32H&R Mag.  Brings most any knockdowns at the old Winter Range and the old EOT shoots.

Posted

I've seen promo used as well

Posted

I have been loading 32 S&W Long with 1.7 of Bullseye and a 100 grain bullet. Grandson has been taking down knockdowns easier than some peoples 38 loads

Posted

I have trail Boss ,Clays and W 296. 32 H&R cases I have some 32 S & W longs also.

 

Posted

I've used 2.3 gr Clays and a 100gr bullet in .32 mag case.  I also have used Universal Clays with good results.

 

Kajun

Posted
2 hours ago, Crazy Gun Barney, SASS #2428 said:

can't believe one of my favorite powders hasn't been mentioned yet... fffg

Perhaps you didn't read the previous posts. :mellow:

 

Posted
3 hours ago, Crazy Gun Barney, SASS #2428 said:

can't believe one of my favorite powders hasn't been mentioned yet... fffg

Better yet in those small cases, FFFFG.  Plenty of smoke and boom.

Posted
4 hours ago, Pit Bull Tex said:

I have trail Boss ,Clays and W 296. 32 H&R cases I have some 32 S & W longs also.

 

w296 is a powder that is more suitable for magnum loads in larger cases.

Archived

This topic is now archived and is closed to further replies.

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.