Buckshot Bear Posted September 19, 2021 Share Posted September 19, 2021 Just noticed this crack in the wood of a pretty new Stoeger. Link to comment Share on other sites More sharing options...
Colorado Coffinmaker Posted September 19, 2021 Share Posted September 19, 2021 The stock needs to be relieved and fitted to the Stoeger frame and tangs. The crack needs filled with epoxy and the whole shebang bedded with Acraglass. The wood above the crack is going to splinter off. Link to comment Share on other sites More sharing options...
Buckshot Bear Posted September 19, 2021 Author Share Posted September 19, 2021 7 minutes ago, Colorado Coffinmaker said: The stock needs to be relieved and fitted to the Stoeger frame and tangs. The crack needs filled with epoxy and the whole shebang bedded with Acraglass. The wood above the crack is going to splinter off. I'm thinking it likely to eventually splinter off as well. Link to comment Share on other sites More sharing options...
Sam Sackett Posted September 19, 2021 Share Posted September 19, 2021 I agree. This isn’t the first Stoger that wasn’t inletted enough. This allows the recoil forces to hit there, instead of inside on the anchor lug. Relieve the inletting and get those forces moved back inside where they belong. Once that is done and the stock is bedded into the anchor lug, glue and pin the cracked area. Should last a long time. Sam Sackett Link to comment Share on other sites More sharing options...
Ripsaw Posted September 19, 2021 Share Posted September 19, 2021 Short grain on the stock there, too. Wood's gonna be wood. Link to comment Share on other sites More sharing options...
Buckshot Bear Posted September 19, 2021 Author Share Posted September 19, 2021 Thanks fella's I was thinking of drilling two long holes and turning down some walnut that I have and making walnut dowel to the diameter of the smallish drilled holes and dowelling and glueing. I have to admit that my knowledge of you guys saying "it needs inletting and bedding" is over my knowledge threshold of even understanding what you mean as to what needs to be done. Link to comment Share on other sites More sharing options...
Ripsaw Posted September 19, 2021 Share Posted September 19, 2021 The problem is as much the short grain in the stock at that point. In other words, the grain angle is diagonal across the stock rather than parallel with the stock. Short grain is fragile by comparison to long grain (parallel to the stock). There could also be a crack in the wood from the mfg or milling process. May be tough to fix that, but reinforcing the stock with dowel stock is not a bad idea. Inletting and relieving the stock involves removing stock so that the recoil forces are resisted by a solid facing on the stock, in a direction parallel to the stock. I'm not sure that's possible when the grain is running off like it is at the stock's wrist. I'd give the reinforcing a try, but be prepared to replace the stock. If it were Ruger or other reputable mfg, you might get some relief from them, but it's a Stoeger. Que Sera Sera. Link to comment Share on other sites More sharing options...
Buckshot Bear Posted September 19, 2021 Author Share Posted September 19, 2021 14 minutes ago, Ripsaw said: I'd give the reinforcing a try, but be prepared to replace the stock. If it were Ruger or other reputable mfg, you might get some relief from them, but it's a Stoeger. Que Sera Sera. I bought it mail order from another State, I can imagine that a warranty claim would be a right royal pain in the behind + I've slicked it up so that would be an 'out' for them (pretty sure that Beretta Australia is the importer here in Oz). I was thinking of drilling and dowelling from the bottom? Link to comment Share on other sites More sharing options...
Snakebite Posted September 19, 2021 Share Posted September 19, 2021 What you need is Butt Crack Putty Link to comment Share on other sites More sharing options...
Rattlesnake Slim Posted September 19, 2021 Share Posted September 19, 2021 14 minutes ago, Buckshot Bear said: I bought it mail order from another State, I can imagine that a warranty claim would be a right royal pain in the behind + I've slicked it up so that would be an 'out' for them (pretty sure that Beretta Australia is the importer here in Oz). I was thinking of drilling and dowelling from the bottom? But that won't solve the problem of the fit. If you aren't comfortable with the inletting, you can simply use a piece of old credit card plastic to make a spacer to go between the tang and the stock. Cut it the size of the tang and drill a hole for the bolt. It may leave a space between the metal and wood, but that's better than splitting your newly repaired stock. BTW, I do this on every Stoeger I buy BEFORE they split. Link to comment Share on other sites More sharing options...
Frontier Lone Rider Posted September 19, 2021 Share Posted September 19, 2021 MGW sells Stoeger replacement stocks. I have never been able to get one from Stoeger. Link to comment Share on other sites More sharing options...
Buckshot Bear Posted September 19, 2021 Author Share Posted September 19, 2021 2 minutes ago, Rattlesnake Slim said: But that won't solve the problem of the fit. If you aren't comfortable with the inletting, you can simply use a piece of old credit card plastic to make a spacer to go between the tang and the stock. Cut it the size of the tang and drill a hole for the bolt. It may leave a space between the metal and wood, but that's better than splitting your newly repaired stock. BTW, I do this on every Stoeger I buy BEFORE they split. Its Sunday morning here, not sure if I had a hard Saturday night or I'm just thick (didn't have a hard Saturday night so that must mean the later ) but I really don't follow what inletting the stock at the union between the wood and the steel actually means? Link to comment Share on other sites More sharing options...
Rattlesnake Slim Posted September 19, 2021 Share Posted September 19, 2021 The stock is splitting because the receiver is hitting the stock near the crack with every shot. You need to create some space. You can either inlet the stock near the receiver (and everywhere else it is touching) or add a spacer at the back where the tang touches the stock. Link to comment Share on other sites More sharing options...
Buckshot Bear Posted September 19, 2021 Author Share Posted September 19, 2021 9 minutes ago, Rattlesnake Slim said: The stock is splitting because the receiver is hitting the stock near the crack with every shot. You need to create some space. You can either inlet the stock near the receiver (and everywhere else it is touching) or add a spacer at the back where the tang touches the stock. Do you mean relieve the wood where I've marked green? Link to comment Share on other sites More sharing options...
Rattlesnake Slim Posted September 19, 2021 Share Posted September 19, 2021 Yes, that's one option, and anywhere else it touches. Once you get the stock off it should be obvious where the wood has been crushed by the receiver. Link to comment Share on other sites More sharing options...
Abilene Slim SASS 81783 Posted September 19, 2021 Share Posted September 19, 2021 Inletting means creating more space between the stock and receiver where the contact pressure is uneven. Kinda like when a dentist removes material after filling your tooth. Too much filling, the tooth above/below the new filling makes contact putting uneven pressure on it. If left uncorrected, the tooth can fracture. Link to comment Share on other sites More sharing options...
Singin' Sue 71615 Posted September 19, 2021 Share Posted September 19, 2021 I'm still laughing at the title!! Link to comment Share on other sites More sharing options...
Eyesa Horg Posted September 19, 2021 Share Posted September 19, 2021 It did create an image didn't it Sue! Link to comment Share on other sites More sharing options...
Go West Posted September 19, 2021 Share Posted September 19, 2021 It's an unofficial "Plumber's" model. Most agree it's not sexy. Link to comment Share on other sites More sharing options...
Zach Taylor,SASS#14359 Posted September 19, 2021 Share Posted September 19, 2021 Not an uncommon problem with Stoeger stocks, I had one where the stock chipped of on the opposite side of yours, I repaired it with epoxy and it has held up. Link to comment Share on other sites More sharing options...
Colorado Coffinmaker Posted September 19, 2021 Share Posted September 19, 2021 I don't know how helpful this may be, but in a "pinch," the wise folks at Duluth Trading may provide "Derriere Repair." Might could be helpful ??? In light of the OP title perhaps ?? Maybe ?? Link to comment Share on other sites More sharing options...
Warden Callaway Posted September 19, 2021 Share Posted September 19, 2021 Classic example of making a stock with the grain going the wrong direction. Only destiny is to fail. Root out behind crack and fill with Acrglas. Link to comment Share on other sites More sharing options...
The Original Lumpy Gritz Posted September 19, 2021 Share Posted September 19, 2021 14 hours ago, Singin' Sue 71615 said: I'm still laughing at the title!! I choked some on my Whisky when I first read it OLG Link to comment Share on other sites More sharing options...
Marshal TKD, Sass # 36984L Posted September 19, 2021 Share Posted September 19, 2021 This thread could have went all kinds of sideways, Sadly it did not. Link to comment Share on other sites More sharing options...
Imis Twohofon,SASS # 46646 Posted September 19, 2021 Share Posted September 19, 2021 27 minutes ago, Marshal TKD, Sass # 36984L said: This thread could have went all kinds of sideways, Sadly it did not. "Day ain't over yet" Curly- City Slickers Imis Link to comment Share on other sites More sharing options...
Sedalia Dave Posted September 19, 2021 Share Posted September 19, 2021 Google how to fit a butt stock Link to comment Share on other sites More sharing options...
SHOOTIN FOX Posted September 19, 2021 Share Posted September 19, 2021 Google anvil gunsmithing and watch the videos. A screw and acraglass is better that pinning with a dowel. Be patient and do it right the first time., saves aggravations later. Link to comment Share on other sites More sharing options...
Lazy Eeyour Posted September 20, 2021 Share Posted September 20, 2021 After you relieve the stock, find a diabetic friend who uses syringes and 32 gauge, very fine, needles. Fill with Tite Bond and slowly fill the crack at various locations. Clamp and wait a few (3) days. Link to comment Share on other sites More sharing options...
Larsen E. Pettifogger, SASS #32933 Posted September 20, 2021 Share Posted September 20, 2021 If I remember coreectly the stock in that area is pretty thin and you might do more damage by trying to drill it and use a dowel or screw. Fill and bond is the way to go. There are some videos on the Midway website that show crack repair. Here is a short clip from one. Link to comment Share on other sites More sharing options...
Dusty Devil Dale Posted September 20, 2021 Share Posted September 20, 2021 At first glance, I thought that title was somebody's Alias. Link to comment Share on other sites More sharing options...
"Big Boston" Posted September 30, 2021 Share Posted September 30, 2021 Between some of Midway USA videos and some of Anvils videos, I've fixed some pretty ugly ones. Plan out your work first, your first kick at the cat is your best opportunity for success. The 97 in the pictures has dowels, arsenal pins, glue and epoxy. The shotgun was pretty much garbage to begin with, it took lots of work and parts. That poor forend was in 4 pieces, at the time I could not find a three screw forend for sale. I'm no craftsman, and the pictures are just to illustrate what can be done if you think things out and take your time. Link to comment Share on other sites More sharing options...
Yusta B. Posted September 30, 2021 Share Posted September 30, 2021 If you end up pinning it, use some brass machine screws. The threads will hold better than a dowel. Should also be bedded. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.