Shooting Bull Posted February 19, 2020 Share Posted February 19, 2020 When cocking one of my pistols it binds up occasionally. Definitely not a high primer since it does it unloaded too. I'll detail strip it and drop all parts in an ultrasonic cleaner. Problem goes away for a while but then comes right back. I'm not even sure what exactly to look for. My thoughts were the plunger on the hammer binding up but when it's out of the gun it works just fine. Gun functions perfectly other than the occasional binding. Any suggestions for things to check before sending it to someone who knows more about it than I do? Link to comment Share on other sites More sharing options...
Jed Cooper Posted February 19, 2020 Share Posted February 19, 2020 Check to see that the cylinder base pin is in all the way. If it’s not it can cause the transfer bar to be locking you up. Link to comment Share on other sites More sharing options...
Randy Saint Eagle, SASS # 64903 Posted February 19, 2020 Share Posted February 19, 2020 I would also check to make sure the base pin is true, not bent any. Thanks Randy Link to comment Share on other sites More sharing options...
Sedalia Dave Posted February 19, 2020 Share Posted February 19, 2020 Does it only do this only with cartridges loaded or does it also do it when the pistol is unloaded? Link to comment Share on other sites More sharing options...
Rex M Rugers #6621 Posted February 19, 2020 Share Posted February 19, 2020 15 minutes ago, Sedalia Dave said: Does it only do this only with cartridges loaded or does it also do it when the pistol is unloaded? Dave , re-read second sentence in OP. Rex Link to comment Share on other sites More sharing options...
Abe E.S. Corpus SASS #87667 Posted February 19, 2020 Share Posted February 19, 2020 If the spring loaded plunger on the base pin is sticking, it cannot do its job of pushing the transfer bar to the rear and the T-bar will snag on the firing pin as you are cocking the hammer. Link to comment Share on other sites More sharing options...
Captain Bill Burt Posted February 19, 2020 Share Posted February 19, 2020 Sometimes even if the plunger isn't sticking the T-bar can catch on the firing pin. The next time it binds look there. If the T-bar is stuck on the lower part of the firing pin that's your problem. I solved it by taking the T-Bar out and filing the leading edge on the firing pin side down just a bit. Problem solved. Link to comment Share on other sites More sharing options...
Caboose Posted February 19, 2020 Share Posted February 19, 2020 I had a Ruger Blackhawk once that had a sloppy base pin to cylinder fit. When cocking and the pawl raised to pushed the cylinder around it would push the top rear of cylinder up enough so that the top front part of the cylinder would go down and forward just enough to hit the forcing cone and bind up. I ordered a couple close tolerance base pins from Belt Mountain and the problem was solved. Link to comment Share on other sites More sharing options...
The Original Lumpy Gritz Posted February 19, 2020 Share Posted February 19, 2020 When it happens. Remove the cyl and reinstall the cyl pin. Does it still happen? OLG Link to comment Share on other sites More sharing options...
The Original Lumpy Gritz Posted February 19, 2020 Share Posted February 19, 2020 Any chance you got the cylinders switched? OLG Link to comment Share on other sites More sharing options...
Mack Hacker, #60477 Posted February 19, 2020 Share Posted February 19, 2020 8 minutes ago, The Original Lumpy Gritz said: Any chance you got the cylinders switched? OLG This!!!! And don’t ask me how I know. It’s much worse when it happens to your wife’s guns; again don’t ask me how I know Link to comment Share on other sites More sharing options...
Yusta B. Posted February 19, 2020 Share Posted February 19, 2020 By "bind up" do you mean drags or locks up tight ? Link to comment Share on other sites More sharing options...
Frontier Lone Rider Posted February 20, 2020 Share Posted February 20, 2020 I had this happen, it was the base pin issue. Link to comment Share on other sites More sharing options...
Shooting Bull Posted February 20, 2020 Author Share Posted February 20, 2020 One little bit of information I forgot to mention, my pistols have been short stroked by Lassiter. The don’t have transfer bars anymore. By binding up I mean I can’t cock the hammer. I can pull it back 1/4 of an inch or so and it stops cold. I’ll keep trying and eventually it’ll go to full cock. Link to comment Share on other sites More sharing options...
The Original Lumpy Gritz Posted February 20, 2020 Share Posted February 20, 2020 Just now, Shooting Bull said: One little bit of information I forgot to mention, my pistols have been short stroked by Lassiter. The don’t have transfer bars anymore. By binding up I mean I can’t cock the hammer. I can pull it back 1/4 of an inch or so and it stops cold. I’ll keep trying and eventually it’ll go to full cock. Will they cock correctly when you point the muzzle straight up? Do you see any drag Mark's on the cylinder face? OLG Link to comment Share on other sites More sharing options...
The Original Lumpy Gritz Posted February 20, 2020 Share Posted February 20, 2020 Take some carb cleaner and flush the spring plunger assembly in the base pin. Do you oil the cyl base pin channel in the cylinder? A drop or 2 is a good thing. Take the grips off a see what you can as you cycle the action. OLG Link to comment Share on other sites More sharing options...
Bad Bascomb, SASS # 47,494 Posted February 20, 2020 Share Posted February 20, 2020 Experienced same symptoms. Replaced plunger, pin & spring in hammer (clean its resident hole thoroughly). That was it. If cylinder issues are eliminated, I'm betting on hammer plunger. Often problem with plunger is not obvious to simple scrutiny. Good luck, and advise as to solution. Link to comment Share on other sites More sharing options...
45 Dragoon Posted February 20, 2020 Share Posted February 20, 2020 Yap. ^^ This. Mike Link to comment Share on other sites More sharing options...
Johnny Meadows,SASS#28485L Posted February 20, 2020 Share Posted February 20, 2020 If you get a chance, call me today. 928-300-6684 J.M. Link to comment Share on other sites More sharing options...
Purly SASS # 57438 Posted February 20, 2020 Share Posted February 20, 2020 I am having the exact issues with one of my short strokes Vaqueros. If you get your problem solved I would like to know what the fix was. Thanks. Link to comment Share on other sites More sharing options...
Roscoe Regulator Posted February 20, 2020 Share Posted February 20, 2020 On 2/19/2020 at 1:00 PM, Shooting Bull said: When cocking one of my pistols it binds up occasionally. Definitely not a high primer since it does it unloaded too. I'll detail strip it and drop all parts in an ultrasonic cleaner. Problem goes away for a while but then comes right back. I'm not even sure what exactly to look for. My thoughts were the plunger on the hammer binding up but when it's out of the gun it works just fine. Gun functions perfectly other than the occasional binding. Any suggestions for things to check before sending it to someone who knows more about it than I do? Mine was binding when DEcocking, and it was definitely the hammer plunger. Once having the hammer assy out and in my hand, I could make the plunger bind with the tip of a screwdriver pressing it. I removed the cross pin and immediately lost sight of it. The spring looked fine under magnification as did the plunger. I am going to guess that the plunger got a little crossways and was catching on the cross pin. I ordered a new cross pin along with a complete new set of screws as well as springs for the other plungers. Ruger is sending all no charge. Link to comment Share on other sites More sharing options...
Yusta B. Posted February 20, 2020 Share Posted February 20, 2020 Deleted Link to comment Share on other sites More sharing options...
Assassin Posted February 20, 2020 Share Posted February 20, 2020 I disassembled mine for cleaning a couple days ago. When I put them back together they were binding, removed the cylinder pins, reinstalled and they were fine. They are fine tuned, short stroked, and don't have transfer bars. I'm thinking it was an alignment issue. No, I didn't mix up cylinders or pins, only took one apart at a time. Link to comment Share on other sites More sharing options...
Major BS Walker Regulator Posted February 20, 2020 Share Posted February 20, 2020 Check the loading gate. I had one pistol that the gate spring somehow went bad. After a shot or two the gate base would ride out and bind on the brass. Link to comment Share on other sites More sharing options...
Dusty Devil Dale Posted February 20, 2020 Share Posted February 20, 2020 4 hours ago, Roscoe Regulator said: Mine was binding when DEcocking, and it was definitely the hammer plunger. Once having the hammer assy out and in my hand, I could make the plunger bind with the tip of a screwdriver pressing it. I removed the cross pin and immediately lost sight of it. The spring looked fine under magnification as did the plunger. I am going to guess that the plunger got a little crossways and was catching on the cross pin. I ordered a new cross pin along with a complete new set of screws as well as springs for the other plungers. Ruger is sending all no charge. The base pin could be the problem, if it is loosely fitted it could be allowing the cylinder occasionally to drop down and narrow the cylinder latch clearance. Also check the operation of the base pin end plunger. But if I were you, I'd start with the hammer plunger. The retention flat area on the plunger is very thin. It will bend with very little force applied. The slightest bend can cause it to bind unpredictably against its retention pin or one side of its hole. I would start by installing a new plunger and spring, regardless of how good they might appear. The replacements are very inexpensive. You might also take note whether the jamb occurs always on the same cylinder. Your problem could be from the bolt not depressing far enough to release the cylinder latch on one or more cylinders, similar to the loose base pin problem above. That would prevent the cylinder rotating during cocking of the hammer. Just a couple thoughts. Link to comment Share on other sites More sharing options...
The Original Lumpy Gritz Posted February 20, 2020 Share Posted February 20, 2020 21 minutes ago, Dusty Devil Dale said: You might also take note whether the jamb occurs always on the same cylinder. Don't you mean chamber? OLG Link to comment Share on other sites More sharing options...
"Big Boston" Posted February 21, 2020 Share Posted February 21, 2020 There's not that many parts in a NMV, but they all have to move pretty freely. They need some oil. I had the same hang-up. That little pin just barely has enough pressure to get the job done, IMHO. If anything it touches or pushes is stiff, it binds. After it happened to me I check each of my hipguns before each meet. It's a fairly easy check. What you don't want to see is the cylinder latch dropping too soon after being lifted out of the notch. Ideally I like to see the pin drop about at the 1/2 way mark. Half way between the notch and the beginning of the lead in cutaway for the next notch. Hopefully you can see the faint mark just before the usual dropping point for the cylinder latch. On the gun I had the issue the latch was dropping almost immediately after clearing the notch. Unfortunately it's a stainless gun, doesn't make for a clear picture. Link to comment Share on other sites More sharing options...
Cemetery Posted February 21, 2020 Share Posted February 21, 2020 On 2/19/2020 at 2:31 PM, Mack Hacker, #60477 said: It’s much worse when it happens to your wife’s guns; again don’t ask me how I know Must have been a long ride home, if that happened on a match day. Link to comment Share on other sites More sharing options...
Dusty Devil Dale Posted February 21, 2020 Share Posted February 21, 2020 2 hours ago, The Original Lumpy Gritz said: Don't you mean chamber? OLG Yes. I guess I can't blame that one on spell check. How about old age? Link to comment Share on other sites More sharing options...
The Original Lumpy Gritz Posted February 21, 2020 Share Posted February 21, 2020 5 minutes ago, Dusty Devil Dale said: Yes. I guess I can't blame that one on spell check. How about old age? Workz for me OLG Link to comment Share on other sites More sharing options...
Tye Riverman, SASS #41433 Posted February 22, 2020 Share Posted February 22, 2020 I had a similar problem and it was the retaining pin that held in the plunger and spring on the hammer assembly. There was a burr on the retaining pin and it was a pain to find. The plunger was hanging up on the retaining pin. Had that thing apart many times, but only found it after I completely removed it from the hammer assembly. I was only pushing it out far enough to remove the pluncher assembly and it remained hidden in the hammer. My gun was not short stroked but the hammer safety was removed, hammer welded, half cock, etc. Hope this helps. Tye Link to comment Share on other sites More sharing options...
Bad Bascomb, SASS # 47,494 Posted February 22, 2020 Share Posted February 22, 2020 Yep----^^^^ amazingly simple, yet so subtley hidden. Are ya fixed yet? Link to comment Share on other sites More sharing options...
Shooting Bull Posted February 22, 2020 Author Share Posted February 22, 2020 Sorry folks, I’ve been a bit tied up lately handling what the boss tells me are higher priorities. I’ll dig into it and give a full report ASAP. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.