Max Payne Posted March 7, 2021 Posted March 7, 2021 When I acquired Ophelia's 32 Single-Sixes, the front sights were filed to point of aim. I installed Sure-Hits on all 3 of her pistols & filed them to the same profile that they already had. We have discovered that she needs more of the blade in her sight picture, so I'd like to remove the ones that are on there & install some new ones without taking them down so far or at all. I don't want to take a chance on screwing around so that the whole front sight comes off, so I'd like to know if anyone has needed to do something like this & has done so successfully. I used the epoxy or whatever the super-duper liquid is that came with the Sure-Hits when installing them. I was advised by a reliable source that I could heat them up & then drive a small screwdriver in to pry them loose, but I'd like to get some more feedback before I do anything I might regret. Feedback, please.
Ozark Shark Posted March 7, 2021 Posted March 7, 2021 Call Frank and see what he recommends. http://www.surehitsights.com/about-us.html
Abilene, SASS # 27489 Posted March 7, 2021 Posted March 7, 2021 Saw off the barrels right behind the sights and dovetail in new ones? I'm pretty sure that's what Coffinmaker would say.
Snakebite Posted March 7, 2021 Posted March 7, 2021 Have you tried a little heat? I'm not saying it will work but I would cautiously give it a try. What's to loose? Worse case is you use too much heat and the sight comes out.... so what, then you just put in another one. Snakebite
SGT. ELI 35882 GUNFIGHTER Posted March 7, 2021 Posted March 7, 2021 It is 680 green locktite a little heat should loosen them up so you can pop them off.
MBFields Posted March 7, 2021 Posted March 7, 2021 Use a hair dryer and heat them, they will come off or a small butane torch.
Randy Saint Eagle, SASS # 64903 Posted March 7, 2021 Posted March 7, 2021 Max, once you put the new ones on I used JB Weld to fill in above the factory sight. Then I had something solid one I filed them without going down to the factory sight. I also filed them down on the range so I could file a little and then shoot until I got them where I wanted. Randy
Sixgun Seamus Posted March 8, 2021 Posted March 8, 2021 Heated mine with a hair dryer and they pried off easily.
Captain Bill Burt Posted March 8, 2021 Posted March 8, 2021 11 hours ago, Sixgun Seamus said: Heated mine with a hair dryer and they pried off easily. I did the same thing.
Max Payne Posted March 8, 2021 Author Posted March 8, 2021 All good feedback. I did talk to Slick, & he said that others had done the heat & pry successfully, but had not done it himself. Thought I would get some feedback from those with personal experience. By the way, he answered his phone on Sunday evening & discussed this with me. Sounds like my 1st move is dryer & prying. I also have a heat gun if I need to step it up. Thanks everybody.
Tyrel Cody Posted March 8, 2021 Posted March 8, 2021 Ok, I'm disappointed in everyone here, this has gone on way too long without someone asking... Sights? What are those?
Marshal TKD, Sass # 36984L Posted March 8, 2021 Posted March 8, 2021 Max 1/2 pound of Tannerite should fix your front sight problem.
DeaconKC Posted March 8, 2021 Posted March 8, 2021 13 minutes ago, Marshal TKD, Sass # 36984L said: Max 1/2 pound of Tannerite should fix your front sight problem. "Candygram for Mongo"
TN Mongo, SASS #61450 Posted March 9, 2021 Posted March 9, 2021 Curly Bill Kelly of Harriman, TN does a very nice job of replacing Ruger front sights with solid brass sights, if that is something you're interested in.
Joe LaFives #5481 Posted March 9, 2021 Posted March 9, 2021 Just paint the back of the sight with gold nail polish - renew it periodically.
Max Payne Posted March 10, 2021 Author Posted March 10, 2021 11 hours ago, Cowboy Junky said: This isn't my fault is it Max? lol....... It somehow probably is!
Max Payne Posted March 10, 2021 Author Posted March 10, 2021 On 3/8/2021 at 9:31 AM, Marshal TKD, Sass # 36984L said: Max 1/2 pound of Tannerite should fix your front sight problem. There you go!
Buck Garrett Posted March 12, 2021 Posted March 12, 2021 Just finished removing sure hits on 2 stainless Rugers. Used a heat gun, a thin blade pocket knife, and a 1" nylon/brass hammer. Placed gun in a vise, and heated the sight. Positioned the edge of knife blade on the glued joint, and tapped gently until it wedged apart the brass from the sight blade. Eazy peezy. Now how do I get the glue residue off. Tried some acetone to no avail. Didn't have any lacquer thinner on hand. Suggestions please.
Ya Big Tree Posted March 13, 2021 Posted March 13, 2021 14 hours ago, Buck Garrett said: Just finished removing sure hits on 2 stainless Rugers. Used a heat gun, a thin blade pocket knife, and a 1" nylon/brass hammer. Placed gun in a vise, and heated the sight. Positioned the edge of knife blade on the glued joint, and tapped gently until it wedged apart the brass from the sight blade. Eazy peezy. Now how do I get the glue residue off. Tried some acetone to no avail. Didn't have any lacquer thinner on hand. Suggestions please. I did the same thing, except I used a razor blade instead of the knife. Soaked for awhile in acetone (I don't know if that helped or not) then cleaned the rest of the glue off with the razor blade and then polished. Mine were stainless steel so I didn't have to worry about the finish.
Recommended Posts
Archived
This topic is now archived and is closed to further replies.