Dee Mak Jack, SASS #55905 Posted December 6, 2023 Share Posted December 6, 2023 Have a Ruger Wrangler 22 that has tite/rough (?) cylinder bores. Can’t figure a way to polish them as they are so small. Anyone have an idea on this? Link to comment Share on other sites More sharing options...
Tex Jones, SASS 2263 Posted December 6, 2023 Share Posted December 6, 2023 You might want to edit the header. Link to comment Share on other sites More sharing options...
Widder, SASS #59054 Posted December 7, 2023 Share Posted December 7, 2023 1 hour ago, Tex Jones, SASS 2263 said: You might want to edit the header. Yea......nobody likes a small tit. ..........Widder Link to comment Share on other sites More sharing options...
Mustang Gregg Posted December 7, 2023 Share Posted December 7, 2023 That's funny right there! Link to comment Share on other sites More sharing options...
Buckshot Bear Posted December 7, 2023 Share Posted December 7, 2023 1 hour ago, Tex Jones, SASS 2263 said: You might want to edit the header. Or tell us where to buy one Link to comment Share on other sites More sharing options...
Sam Sackett Posted December 7, 2023 Share Posted December 7, 2023 They usually come in pairs! Don’t know as you can get just one…….. Something like Lays tater chips…….. Sam Sackett Link to comment Share on other sites More sharing options...
Garrison Joe, SASS #60708 Posted December 7, 2023 Share Posted December 7, 2023 I'd do this with a chamber polishing flexi-hone. Brownells has a "22 magnum" hone that if you wrap some tape around it to limit the travel into the chamber just far enough for .22 LR, would probably take the roughness out. 800 grit. Get their "flexi-hone" oil, as if you use other oils it can soften the adhesive that holds the abrasive balls together on the brush. https://www.brownells.com/tools-cleaning/paint-metal-prep/abrasives-polishing/rifle-polishing-system/ Go slow, follow their instructions, use the special oil. I've used these on rough .38 special chambers, .45 colt, the mainspring housing bore of 1911 pistols, 12 gauge chambers and forcing cones. They really polish up a chamber/bore! Realize that the manufacturer states this is for a .22 magnum chamber. So, you will want to use it very lightly, and in the fine grit (800) it should not make the .22 LR chambers too sloppy. No guarantees that it will hold to a perfect .22 LR chamber, though. An alternative would be to make up a honing tool yourself, perhaps a 0.200" diameter (or 3/16") brass rod that you split with a fine jewelers saw blade enough to hold one wrap of 400 grit sandpaper. Turn very slow with a drill. Another alternative - if you want a strong guarantee - get a finish reamer for .22 LR. It'll be $200 to buy, so look to (I believe) a company "4D" for a rental reamer. You may want to be real careful so you do not ding it and incur a regrind/replacement charge. If you have a local gunsmith who cuts barrels and chambers, you could have him rent one and do the work. This will cut any part of the chamber clean which was not cut well at factory. It will not remove "too-deep" gouges Have you checked with Ruger to see if they will do this work as a warranty job? good luck, GJ Link to comment Share on other sites More sharing options...
Buckshot Bear Posted December 7, 2023 Share Posted December 7, 2023 2 hours ago, Widder, SASS #59054 said: Yea......nobody likes a small tit. ..........Widder Link to comment Share on other sites More sharing options...
Kid Rich Posted December 7, 2023 Share Posted December 7, 2023 I would use 600 to 800 grit automotive finishing cloth, the finer the grit the better job of POLISHING it does. kR Link to comment Share on other sites More sharing options...
Assassin Posted December 7, 2023 Share Posted December 7, 2023 Long cotter pin, sandwich a piece of abrasive cloth inside pin, chuck it into a drill and spin it in each chamber. Don't get overly agressive. Link to comment Share on other sites More sharing options...
The Original Lumpy Gritz Posted December 7, 2023 Share Posted December 7, 2023 Have you contacted Ruger? You can try a .25 cal bore mop in a drill motor, and toothpaste. Link to comment Share on other sites More sharing options...
Oak Ridge Regulator Posted December 7, 2023 Share Posted December 7, 2023 I used a very fine grit lapping compound on a 22 cal mop. It dident take much to smooth the chambers out so you want to go slow and check for fit often Link to comment Share on other sites More sharing options...
Widder, SASS #59054 Posted December 7, 2023 Share Posted December 7, 2023 1 hour ago, The Original Lumpy Gritz said: Have you contacted Ruger? You can try a .25 cal bore mop in a drill motor, and toothpaste. One of the better toothpaste I have tried with good results for polishing is the 'Charcoal' type toothpaste. But, one word of warning..... don't try to clean it up with cleaning oils or cleaning solutions. It don't seem to wash away easy with oil. BUT, if you clean it out with water, it cleans up easy. Some of the best advice on this thread was posted above by Garrison Joe. He shares a lot of good stuff with us on the Wire. ..........Widder Link to comment Share on other sites More sharing options...
Eyesa Horg Posted December 7, 2023 Share Posted December 7, 2023 1 hour ago, Widder, SASS #59054 said: Garrison Joe. He shares a lot of good stuff with us on the Wire +1 Link to comment Share on other sites More sharing options...
Edward R S Canby, SASS#59971 Posted December 7, 2023 Share Posted December 7, 2023 I have a BL-22 rimfire rifle that will not feed Federal Premium .22s reliably. However, it will feed some ARMSCOR .22s I bought years ago all day. Try another brand of .22s. They might work in your firearm. Link to comment Share on other sites More sharing options...
Tommy Reb Posted December 7, 2023 Share Posted December 7, 2023 I had a Ruger Wrangler with extremely rough cylinder chambers. Tool marks were clearly visible in the chambers. Cartridges would go in easily, but after firing had to be tapped out with a rod and hammer. I called Ruger, explained the problem and they sent me a new cylinder which works fine. I was surprised they would send me a cylinder. I had expected I would have to send the gun in for a cylinder to be fitted. That probably tells us something about the degree of hand fitting on Wranglers. TR Link to comment Share on other sites More sharing options...
Assassin Posted December 8, 2023 Share Posted December 8, 2023 Wranglers are $200 guns. I wouldn't expect a fine tuned action job. I'm just happy they're available, inexpensive, great starter guns for novice shooters. Link to comment Share on other sites More sharing options...
watab kid Posted December 8, 2023 Share Posted December 8, 2023 i agree with the above , but i think you can improve your experience with some of the above suggestion's , the tooth paste is simply a flavored and edible rouge - used it to polish things ive made for years [i had a source for "test" tooth paste back in the 60s - had a couple 2lb coffee cans full and that goes a long way , the gell worked just as good as the paste - just as abrasive to metal in testing lab [my source was trying to improve pumping it on their production lines back then] Link to comment Share on other sites More sharing options...
Bad Bascomb, SASS # 47,494 Posted December 8, 2023 Share Posted December 8, 2023 Took possession of my Super Wrangler today, and immediately took out the small hole gauges and checked both LR and magnum cylinders. To my great surprise and gratification. all holes were consistent and proper. Really stiff, and in need of springs and gentle massage, but very promising. Link to comment Share on other sites More sharing options...
The Original Lumpy Gritz Posted December 8, 2023 Share Posted December 8, 2023 15 hours ago, Tommy Reb said: I had a Ruger Wrangler with extremely rough cylinder chambers. Tool marks were clearly visible in the chambers. Cartridges would go in easily, but after firing had to be tapped out with a rod and hammer. I called Ruger, explained the problem and they sent me a new cylinder which works fine. I was surprised they would send me a cylinder. I had expected I would have to send the gun in for a cylinder to be fitted. That probably tells us something about the degree of hand fitting on Wranglers. TR Says much about modern day machinery! Link to comment Share on other sites More sharing options...
Garrison Joe, SASS #60708 Posted December 8, 2023 Share Posted December 8, 2023 Says more about the machine operator not paying attention to when tooling needs sharpening! And then too little QA. All to save costs, I would guess GJ Link to comment Share on other sites More sharing options...
watab kid Posted December 10, 2023 Share Posted December 10, 2023 cant argue that - trying to get too much from a tool before changeout , i dont think the operators today have that much control over the machine thats all controlled by the computers but the tool changeouts is critical , trying to get too much production from a setup or inferior tools Link to comment Share on other sites More sharing options...
Beans Ahgin Posted December 15, 2023 Share Posted December 15, 2023 I used to use the split brass tubing method with a leather wrap and talcum powder as the abrasive. And then came the lawsuits right about the time I ran out of talc. The Missus now wonders why we need to try so many different brands/types of toothpaste, and why after 42 years of marriage I have now seemingly taken to brushing my teeth in the workshop. Link to comment Share on other sites More sharing options...
watab kid Posted December 15, 2023 Share Posted December 15, 2023 thats a good one , let me know how you work that response out - i may need it Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.