seen on table saw fence question for our woodworkers on a table saw accessory

[Cheyenne Ranger, 48747L]

I've seen this on several videos and wondered what it is an what's it for

 

looks like it has a handle then four interlocking gears

 

any help appreciated

 

[The Shoer 27979]

All I can tell you is it is a home made gagit not sure what it would be used for

Sorry I can't help

[Yul Lose]

No idea.

[Crooked River Pete, SASS 43485]

Link to video? Ask the video guy what it is.

[Utah Bob #35998]

My guess would be some kind of micro adjuster.

[Eyesa Horg]

It's a gizmo 

[Cholla]

4 hours ago, Utah Bob #35998 said:

My guess would be some kind of micro adjuster.

This is my guess as well. Post the video links.

[Wallaby Jack, SASS #44062]

11 hours ago, Cheyenne Ranger, 48747L said:

I've seen this on several videos and wondered what it is an what's it for

 

looks like it has a handle then four interlocking gears

 

any help appreciated

 

 

 .... a SteamPunk thingy

 

[Charlie Harley, #14153]

I’ve been building furniture for 40+ years and never seen something like that.  
 

With context from a video you might have discovered a tool I need to add to my collection.

[LawMan Mark, SASS #57095L]

18 hours ago, Cheyenne Ranger, 48747L said:

I've seen this on several videos and wondered what it is an what's it for

 

looks like it has a handle then four interlocking gears

 

any help appreciated

 

Table Saw Arbor Nut Wrench.  https://ibuildit.ca/projects/table-saw-nut-wrench/

[Eyesa Horg]

Cool, but seems like a lot of work to avoid raising the blade and using a wrench. But that's just me.

[LawMan Mark, SASS #57095L]

1 hour ago, Eyesa Horg said:

Cool, but seems like a lot of work to avoid raising the blade and using a wrench. But that's just me.

It doesn't tighten the arbor nut.  It starts it on the arbor, and spins it down to where it needs to be tightened with a standard wrench.

 

[Gateway Kid SASS# 70038 Life]

1 hour ago, Charlie Harley, #14153 said:

I’ve been building furniture for 40+ years and never seen something like that.  
 

With context from a video you might have discovered a tool I need to add to my collection.

After watching the video you definitely need one just for the “cool” factor. 
Besides you could be the only one on your block to have one. 

Regards

    

Gateway Kid

[Charlie Harley, #14153]

Cool idea!  That widget just screams for a 3-D printer!  If someone could make one at a reasonable cost I’d buy it after scraping my knuckles too many times. 

[Eyesa Horg]

My saw is an old Rockwell and the shaft comes right up to the table. Other than forgetting on occasion that it's left hand thread, it hasn't been an issue. 

I do agree however that the gear gizmo is pretty cool and innovative.

[Colorado Coffinmaker]

Freeking Brilliant.  Also noticed he used the same gear train to run his twin screw End Vice.  It was also meant to be a really FUN project.

[Wallaby Jack, SASS #44062]

20 hours ago, LawMan Mark, SASS #57095L said:

Table Saw Arbor Nut Wrench.  https://ibuildit.ca/projects/table-saw-nut-wrench/

 

16 hours ago, Colorado Coffinmaker said:

Freeking Brilliant.  Also noticed he used the same gear train to run his twin screw End Vice.  It was also meant to be a really FUN project.

 

 Did you also see his 3screw vice mechanism ........