Jump to content
SASS Wire Forum

Archived

This topic is now archived and is closed to further replies.

Hardpan Curmudgeon SASS #8967

"Sight Pusher?"

Recommended Posts

I've always used a small hammer and bass drift to remove/install dovetailed sights.

 

Any experience or recommendations on the "Sight Pusher" devices?  Are they worth the $$?  

Share this post


Link to post
Share on other sites

I've never used a sight pusher, but I have used similar things for other purposes.  
Think of it as using a micrometer to adjust the sight.  Say it had a thread pitch of 80.  One full turn will move what it is pushing against .012".  A quarter turn will move it .003".  How much do you move something with each tap of the hammer?

Share this post


Link to post
Share on other sites

I've never used a sight pusher, but for moving the cross pin on a gearshift socket

IMG_20191207_224916.jpg.8981551fa552853ffc6f844001e244aa.jpg

 

I've used a small C-clamp. Worked fine.

 

Seems like a sight pusher would work as well.

 

Share this post


Link to post
Share on other sites

I had one similar to this one until I broke it. 
it worked well but one must remember to back off the anchor screw for some rear sights...or it may break your adjustment tool. :rolleyes:

https://www.amazon.com/ATG-NcSTAR-Universal-Pistol-Dovetailed/dp/B07GM3LRFF

Share this post


Link to post
Share on other sites

I used one to replace the sights on a Sig.  Definitely had to use one as a hammer and drift would not have worked.  The frame of the pistol was not squared, so it took a bit of adjusting to move the rear sight, but it worked and was easier to use than hammering the sight base.  How often you use one is another matter. 

Share this post


Link to post
Share on other sites

I've got a couple.  Below is a picture of the one i get the most use out of...it's made for Glocks, but will work on other guns as well.  

sight pusher.jpg

Share this post


Link to post
Share on other sites
 

or it may break your adjustment tool.

 

 

You only know that because it says so in the owners manual.  :D

Share this post


Link to post
Share on other sites

The big benefit is for guys installing night sights that contain a capsule for the glow stuff (love tech terms)   They can break if you try to tap them in.  And the ability nudge the sight slightly.        GW

Share this post


Link to post
Share on other sites

Some are good, some are bad and some only work on certain brands of firearms.  After trying one similar (or the same) in Lawman Mark's post, I think I'd rather spend the money and have a gun store/gun smith replace the sights.

Share this post


Link to post
Share on other sites

I ordered one Friday night.

https://www.amazon.com/Pusher-Master-Install-Handguns-Yourself/dp/B00BD65Y4C/ref=sr_1_6?crid=2891PP66GTR2C&dchild=1&keywords=sight+press&qid=1575867527&sprefix=sight+%2Caps%2C201&sr=8-6

 

For a couple of projects spinning around, once you added the shipping prices are the same.

Let see how it behave with me.

Share this post


Link to post
Share on other sites
 

I've used this one on many firearms. Fantastic quality and easy to use.

Sight-Tool

 

71NV-1fai-L._AC_SL1500_.jpg

Just wondering. would this tool work on octagon barrels like a Sharps or HiWall?  Or most of are cowboy rifles?      GW

Share this post


Link to post
Share on other sites
 

I've never used a sight pusher, but I have used similar things for other purposes.  
Think of it as using a micrometer to adjust the sight.  Say it had a thread pitch of 80.  One full turn will move what it is pushing against .012".  A quarter turn will move it .003".  How much do you move something with each tap of the hammer?

 

I mark the sight and bb/slide with a pencil so I have a reference. 

OLG 

Share this post


Link to post
Share on other sites
 

 

I mark the sight and bb/slide with a pencil so I have a reference. 

OLG 

 

Even with a pusher I would do that. But I know that with a thread pitch of X I will get so much movement per turn (or half turn).  Tapping with a hammer doesn't give you the same precision. One tap may move it 0.0004" and the next tap may move it 0.002".

Share this post


Link to post
Share on other sites

I use an MGW Sight Pro 1000.  Expensive, but does a fabulous job even on those almost impossible to move Springfield pistol sights.  Doesn't break tritium tubes, etc.

Share this post


Link to post
Share on other sites
 

 

Even with a pusher I would do that. But I know that with a thread pitch of X I will get so much movement per turn (or half turn).  Tapping with a hammer doesn't give you the same precision. One tap may move it 0.0004" and the next tap may move it 0.002".

 

I go by what the target shows me ^_^

Many yrs ago I made a 'pusher' that uses a dial indicator.

That removed all guesswork. 

OLG 

Share this post


Link to post
Share on other sites

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.