Jump to content
SASS Wire Forum
Sign in to follow this  
Phoenix Rising

Reloading questiond

Recommended Posts

So I have a Dillion 650 have reloaded 45 colt on for years.  Mostly I guess the brass came from me buying new ammo shooting it and using the brass again.  I must have added some new starline brass somewhere along the line but I don’t really remember
With more time on my hands l was close to using up all my old brass about 1500 hundred rounds and ordered 500 hundred new starline 45 colt brass

this brass has been really hard to work with. On that second loading point where the brass gets belled out it is heck to get it to come back down. Sometimes shakes my loading bench

is there someway to bell out the brass before using it. Open to any suggestions

Share this post


Link to post
Share on other sites

PR,

Try annealing your brass before loading.Makes loading easier and keeps your guns cleaner by reducing blow-back.

Share this post


Link to post
Share on other sites

Ok, a couple of things, first off .45 LC brass is fairly thick so there are some tricks.  Like @Choctaw Jack said you can anneal your brass that will make the top portion much softer so it'll work better.  Second check your powder/bell die make sure it's clean you may have a build up of crud.  Third, before I load .45LC I spray the cases with Hornady One Shot it makes the brass noticeably easier in the dies.  Hope this helps.  

  • Like 4
  • Thanks 1

Share this post


Link to post
Share on other sites
Posted (edited)

Lube the occasional case mouth inside with non petroleum lube. The new brass is sticking to your case belling die. Your not experiencing the sticking with fired cases is most likely cause they have either residual bullet lube or polishing residue from tumbler media. There are several case lubes that will work, Hornady One Shot like Tequilla Shooter recommends and many others. I use Lee myself.

Edited by Captain Clark
  • Like 2

Share this post


Link to post
Share on other sites

I tumble brand new brass for maybe half an hour or more.  Then use One Shot case lube.

  • Like 3
  • Thanks 2

Share this post


Link to post
Share on other sites

Starline is hard brass.

Try running it through your case cleaner for an hour or two.

OLG 

  • Like 1
  • Thanks 1

Share this post


Link to post
Share on other sites
Posted (edited)

Known problem with new .45 Colt (and Cowboy .45 Special) brass.    Starline knows about it, and has a new profile they will machine into your powder-drop expander tube.   Contact them!

 

Until you get to that, yes, you need to lube the inside of case mouths.  Hornady One Shot case lube is enough to make it easy to lower the shell plate/ram after expanding the mouth.

 

Good luck, GJ

Edited by Garrison Joe, SASS #60708
  • Like 2

Share this post


Link to post
Share on other sites

You need to use this  https://www.midwayusa.com/product/1012767842?pid=319390 

on the new cases, simply dip them into the dry lube container before you size them. The dry lube lubricates the inside neck of the case to prevent it from sticking to the belling die.

 

TB

  • Thanks 1

Share this post


Link to post
Share on other sites
Posted (edited)

A little Hornady OneShot lube (or what you have available) on new cases helps a bunch. Get some inside case mouth too. Normally, after a couple loadings it shouldn't be necessary for pistol caliber brass if you have carbide sizer. Not sure about Dillon 45 Colt expander issue though (make sense).  

Edited by Slimy

Share this post


Link to post
Share on other sites
14 hours ago, Grizzly Dave said:

I tumble brand new brass for maybe half an hour or more.  Then use One Shot case lube.

This;)

Share this post


Link to post
Share on other sites
2 hours ago, Four Eyes Henry said:

Deburr the brass on the inside...

 

 

THIS^^^

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
Sign in to follow this  

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.