Black Mike Posted May 18, 2021 Share Posted May 18, 2021 I have owned a number of Uberti 1873’s I’ve the last dozen years and taking them down for full cleaning has never been an issue. A fellow shooter brought his rifle over to learn how to take it down and put it back together. This rifle was purchased new and had only had a few hundred rounds through it. I took the side plates off then removed the toggles. Then I tried to remove the pin and wedge to remove the firing pin extension and bolt. This pin was in there solid. I tried tapping the pin with a brass punch but could not get it to free up. If it were mine I would have used a bit more force. Any suggestions on how I might free this pin? Link to comment Share on other sites More sharing options...
Lefty Wheeler Posted May 18, 2021 Share Posted May 18, 2021 Support the bolt with a block of hard wood. Tap from left to right. Link to comment Share on other sites More sharing options...
Hawkeye Kid Posted May 18, 2021 Share Posted May 18, 2021 Mike, I have had pins that take more than a brass hammer to remove. A little penetrating oil won’t hurt. Supporting the bolt as Lefty suggested will help focus the hammer force on the pin. Once the pin is removed, a little polishing will make it easier next time. Link to comment Share on other sites More sharing options...
PaleWolf Brunelle, #2495L Posted May 18, 2021 Share Posted May 18, 2021 I'm getting one of these Aluminum block for Uberti 73 and 66 rifle bolts – SBGW (sbgwllc.com) Link to comment Share on other sites More sharing options...
Abilene, SASS # 27489 Posted May 18, 2021 Share Posted May 18, 2021 48 minutes ago, PaleWolf Brunelle, #2495L said: I'm getting one of these Aluminum block for Uberti 73 and 66 rifle bolts – SBGW (sbgwllc.com) That is for removing the extractor pin. Don't know if it supports the bolt properly for the link pin, plus is it usable with the bolt still in the rifle, which the OP needs.? Link to comment Share on other sites More sharing options...
PaleWolf Brunelle, #2495L Posted May 18, 2021 Share Posted May 18, 2021 1 hour ago, Abilene, SASS # 27489 said: That is for removing the extractor pin. Don't know if it supports the bolt properly for the link pin, plus is it usable with the bolt still in the rifle, which the OP needs.? Apparently not. I was thinking further ahead in disassembly & cleaning procedure. Thanks for the clarification. Link to comment Share on other sites More sharing options...
Marauder SASS #13056 Posted May 18, 2021 Share Posted May 18, 2021 There are two different methods of attaching the two parts - the old simple pin and the newer (more authentic) extra part. The pin - part 104: And the new, stronger Uberti style - part 721: Link to comment Share on other sites More sharing options...
G W Wade Posted May 18, 2021 Share Posted May 18, 2021 I used a small deep socket (believe 1/4 in) to support the bolt, while a friend balanced the rifle. Wish mine was more like that. Mine the pins drop out when I turn the rifle over. Been that way since new. GW Link to comment Share on other sites More sharing options...
Go West Posted May 19, 2021 Share Posted May 19, 2021 I had that pin snap in a brand new rifle and it cost me 6 unfired rounds that went over my shoulder. Jim Bowie replaced it with a piece of wire (that will not break) and it's been running for 15 years or more. Link to comment Share on other sites More sharing options...
Marauder SASS #13056 Posted May 19, 2021 Share Posted May 19, 2021 18 hours ago, G W Wade said: I used a small deep socket (believe 1/4 in) to support the bolt, while a friend balanced the rifle. Wish mine was more like that. Mine the pins drop out when I turn the rifle over. Been that way since new. GW If it is the old style with the small pin, you can very slightly enlarge the hole and cut off a standard (NOT high speed) drill bit to use as a bit that fits better and will be significantly stronger. Link to comment Share on other sites More sharing options...
G W Wade Posted May 19, 2021 Share Posted May 19, 2021 2 hours ago, Marauder SASS #13056 said: If it is the old style with the small pin, you can very slightly enlarge the hole and cut off a standard (NOT high speed) drill bit to use as a bit that fits better and will be significantly stronger. The 73 is new style. What is the reason you stated old style, Was thinking of doing that GW Link to comment Share on other sites More sharing options...
Marauder SASS #13056 Posted May 19, 2021 Share Posted May 19, 2021 I was not clear which option you had, so gave advise on the older style. Link to comment Share on other sites More sharing options...
Lawdog Dago Dom Posted May 19, 2021 Share Posted May 19, 2021 This is kinda fun to watch. Link to comment Share on other sites More sharing options...
Yusta B. Posted May 20, 2021 Share Posted May 20, 2021 I cut a piece of 1/2" dia. pipe to a length that will support the bolt with the rifle laying flat on a table. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.