Jailhouse Jim, SASS #13104 Posted November 29, 2019 Share Posted November 29, 2019 So I'm contemplating starting to shoot BAMM/GAMM side matches. BAMM is pretty straight forward with low power lead bullets with or without gas checks. Now with GAMM, what are folks using for loads and are those loads sufficient to cycle the action? Link to comment Share on other sites More sharing options...
Dusty Boddems Posted November 29, 2019 Share Posted November 29, 2019 To function the Garand I use imr 4895 35.8 grains with a 170 gc hitek bullet from quality cast bullets in Roswell,NM. GAMM is not an official side match but sure seem to be a lot of places interested in it. On a note about primers.....they make a specific primer that can be purchased for reloading the Garand but another trick is to seat slightly below flush or do both. GAMM is a hoot! Enjoy! Dusty B. Link to comment Share on other sites More sharing options...
Nasty Newt # 7365 Posted December 2, 2019 Share Posted December 2, 2019 We haven't shot a GAMM yet, but we've talked about doing it. Our plan is armor plate targets and milspec ammunition. Link to comment Share on other sites More sharing options...
Dusty Boddems Posted December 2, 2019 Share Posted December 2, 2019 N.N. Absolutely ar500 and no issues. Even with lead bullets ar500 is mandatory inside 100 yards with the Garand load. Link to comment Share on other sites More sharing options...
H. K. Uriah, SASS #74619 Posted December 2, 2019 Share Posted December 2, 2019 I always enjoy shooting my Krag at these things when everyone else is using a 1903. I don't win, but I get a surprising number of "Where'd you get it?" type questions. Link to comment Share on other sites More sharing options...
H. K. Uriah, SASS #74619 Posted December 2, 2019 Share Posted December 2, 2019 For the Garand, I tend to use GI surplus, and it's not been a problem. Both times! Of course, that's generic stuff. For some reason they would not let me use the ones that had black paint on the tips of the bullets.... I had some red tipped stuff once too, (one round) but it would not cycle the action. If memory serves, I shot that off my back porch back in the days before houses were built behind me and there was no anti-discharge law. Link to comment Share on other sites More sharing options...
Jailhouse Jim, SASS #13104 Posted December 2, 2019 Author Share Posted December 2, 2019 To function the Garand I use imr 4895 35.8 grains with a 170 gc hitek bullet from quality cast bullets in Roswell,NM. GAMM is not an official side match but sure seem to be a lot of places interested in it. On a note about primers.....they make a specific primer that can be purchased for reloading the Garand but another trick is to seat slightly below flush or do both. GAMM is a hoot! Enjoy! Dusty B. Do you gas check them? Link to comment Share on other sites More sharing options...
Jailhouse Jim, SASS #13104 Posted December 2, 2019 Author Share Posted December 2, 2019 We haven't shot a GAMM yet, but we've talked about doing it. Our plan is armor plate targets and milspec ammunition. It's a pretty long day trip to Ridgecrest but I'd be interested in coming over if you get something going. Link to comment Share on other sites More sharing options...
Dusty Boddems Posted December 2, 2019 Share Posted December 2, 2019 JJ, yes sir I run gas check on all my surplus rifle. Quality cast has the .310 ready to go hitek coated and gas check. They also make an 8mm in 323 and .325 and a .313 and a 6.5 Swede bullet all hitek coated with gas check ready to go for BAMM and GAMM . Good bullets with fast service and a heck of a good guy to boot. Link to comment Share on other sites More sharing options...
Nasty Newt # 7365 Posted December 3, 2019 Share Posted December 3, 2019 I always enjoy shooting my Krag at these things when everyone else is using a 1903. I don't win, but I get a surprising number of "Where'd you get it?" type questions. I've got about everything but a 1903. I could be competitive with my k98 Mauser but my grandson likes it so I shoot an Enfield, Steyr, Berthier, Krag, or Mosin-Nagant. I sometimes shoot several in a six stage match. I love shooting those old bolt actions. Link to comment Share on other sites More sharing options...
Nasty Newt # 7365 Posted December 3, 2019 Share Posted December 3, 2019 It's a pretty long day trip to Ridgecrest but I'd be interested in coming over if you get something going. I will be sure and let you know. It would be good to see you. Didn't you shoot Defend the Roost a time or two? I could have you confused with somebody else. Link to comment Share on other sites More sharing options...
Bad Bascomb, SASS # 47,494 Posted December 3, 2019 Share Posted December 3, 2019 I recall JJ and Howdy Doody both at DTR. Those were GOOD times. Link to comment Share on other sites More sharing options...
Jailhouse Jim, SASS #13104 Posted December 3, 2019 Author Share Posted December 3, 2019 Yes I have and sure do miss Just George and the match. Link to comment Share on other sites More sharing options...
LostVaquero Posted December 3, 2019 Share Posted December 3, 2019 Local group has more a practice than a match that I call SAMM. SemiAuto. While there is Garand, I bring along a real Wild Bunch Era semi in the form of a Winchester 1907. Remington Model 8 is fine as well both having seen use in the Great War and both being a lot closer to the WB era than a Garand. Link to comment Share on other sites More sharing options...
Dusty Boddems Posted December 3, 2019 Share Posted December 3, 2019 LV, I know I’ve asked you before but please tell me again about your 351. Are you using lead? Did you have to modify the inertia bar to make it run? Will it run on less than a full house load? Link to comment Share on other sites More sharing options...
LostVaquero Posted December 3, 2019 Share Posted December 3, 2019 LV, I know I’ve asked you before but please tell me again about your 351. Are you using lead? Did you have to modify the inertia bar to make it run? Will it run on less than a full house load? Yes I use lead gas check. No I follow old recipies for weight of the bullet in this case 180g. I have not chronographed but a bit lower than a compressed max load ftom an old Lyman manual of 4227. I tried Unique but evrn at max publish would not function properly. Anyway from the manual and making a rough guess probably under 1700 fps. We usually just put up a cowboy steel target out 100m (no idea on the rating but told no jaceted rounds please), and when I hit it just makes a nice BAMM style ring. We only allow BAMM at 1600 fps with lead gas check fine bullets. So far I have found must load near max to get reliable. My 1907 is more than likely an old guard turn in rifle that then sat mostly unused. In very good shape but even though the gun smith opened it up and went through and cleaned guessing spring is still pretty stiff. As I mentioned a top amount of Unique 11gs did not quite do the job. Most reloading sites said imr 4227 was the preferred powder. Old manual says best accuracy load is 171g bullet with 4227 near max of 19.5g but it list this load at 1900 fps which is a bit high to me. Link to comment Share on other sites More sharing options...
Dusty Boddems Posted December 3, 2019 Share Posted December 3, 2019 I’ve got a couple of these and a few 10 round mags. Neat old rifle. I experimented a little without success and went on to other projects. I think it might be time to return to this one. Thank you for your help. Dusty Link to comment Share on other sites More sharing options...
Sedalia Dave Posted December 3, 2019 Share Posted December 3, 2019 Lyman cast bullet handbook has plenty of case bullet loads that should cycle a semi auto. Some 30-06 loads exceed 2500 fps. Keep in mind you need the bullets to be properly sized for the barrel they will be fired in. You absolutely need the PROPER LUBE for the job. Hardness matters but remember Elmer Keith developed the 44 magnum shooting his favorite alloy of 16-1 cast lead. Link to comment Share on other sites More sharing options...
LostVaquero Posted December 3, 2019 Share Posted December 3, 2019 I have not tried yet but Bear Creek indicates they have a coated cast 351 sized bullet at 170g. lyman manual has loadings for 171g so figure close enough. Might give them a try. Western bullet is where I got my 180gs. Bertram brass still makes brass and I picked mine up ftom Grafs. Mine came with a 10 and 5 round mag, never seen the 20. I also got with the rifle the otiginal leather magazine holder. Triple K makes reproduction 10 round mags but some reading indicates they may not work as well as the originals. Anyway while not easy there is still components around for reloading. I think the mini series The Son btought some interest in this old rifle. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.