Ringer Posted May 12, 2020 Share Posted May 12, 2020 Are they worth it? Especially for cowboy. Link to comment Share on other sites More sharing options...
Bucky Buckskin Posted May 12, 2020 Share Posted May 12, 2020 On what Link to comment Share on other sites More sharing options...
Ringer Posted May 12, 2020 Author Share Posted May 12, 2020 Shotgun Link to comment Share on other sites More sharing options...
Bucky Buckskin Posted May 12, 2020 Share Posted May 12, 2020 Had mine done on a shotgun that was done by goatneck Clem he said it would reduce recoil some I liked the gun don’t know if it really reduced the recoil Link to comment Share on other sites More sharing options...
Garrison Joe, SASS #60708 Posted May 12, 2020 Share Posted May 12, 2020 Backboring is often done to allow you to tighten the choke, or to clean up bad pits. I'd not be inclined to do a backbore unless you needed either of those. Barrel has to be checked with barrel calipers to see if there is sufficient metal for that to be safe, too. Backboring itself does not reduce recoil noticeably. But I would lengthen the factory forcing cone in a minute! Even have the reamers and the hones and have done that myself. It does make a bit of reduction to the recoil, and decreases the fouling you get at the forcing cones. I've seen numbers of about 10% felt recoil reduction. There's only a few old guns that I would pre-check before starting, especially those that might need the chamber lengthened out to 2 3/4" plus the forcing cone tapered. Then you should be concerned about final chamber thickness at the forcing cone. If barrel is chrome plated, I wouldn't touch it with machining. Good luck, GJ Link to comment Share on other sites More sharing options...
Ringer Posted May 12, 2020 Author Share Posted May 12, 2020 Thanks GJ Have had the forcing cones done. Was wondering about the other. Link to comment Share on other sites More sharing options...
Garrison Joe, SASS #60708 Posted May 12, 2020 Share Posted May 12, 2020 Sounds like you're done, then. Link to comment Share on other sites More sharing options...
Ringer Posted May 12, 2020 Author Share Posted May 12, 2020 Yep Times 4 or would that be 8? Link to comment Share on other sites More sharing options...
Billy Boots, # 20282 LTG-Regulator Posted May 13, 2020 Share Posted May 13, 2020 I have had Briley backbore numerous SKBs (and, I suspect Briley is probably who did Goatnecks). I like it but not sure worth it for CAS. (NOTE: you will loose most, or all, of the chrome liner of your barrel.) Link to comment Share on other sites More sharing options...
Nasty Newt # 7365 Posted May 14, 2020 Share Posted May 14, 2020 Forcing cones were all the rage when I started about 25 years ago. I don't hear it much any more. Link to comment Share on other sites More sharing options...
Garrison Joe, SASS #60708 Posted May 14, 2020 Share Posted May 14, 2020 Lighter loads being made today by reloaders do away with lots of the need to reduce recoil..... Link to comment Share on other sites More sharing options...
Colorado Coffinmaker Posted May 14, 2020 Share Posted May 14, 2020 A lot depends on the SPECIFIC gun. If you have an older shotgun with 2 1/2 inch chambers, re-chamber and longer forcing cones are a really good idea, IF YOU HAVE ENOUGH METAL. Backboring is only applicable to some guns with bore pitting. If the bores are chrome lined, backboring will remove the lining and potentially turn the barrels to junk. Longer forcing cones will reduce felt recoil. Backboring will not. Link to comment Share on other sites More sharing options...
Eyesa Horg Posted May 15, 2020 Share Posted May 15, 2020 I had the forcing cones lengthened and polished on my Stoeger. It did reduce recoil a little (I think!), but sure made cleaning a lot easier. That 3/4" unpolished section from the factory was a pain to get the plastic out of. The cost was not really worth the result though on a inexpensive SG. Smith estimated $150 and when he got it back from his "specialist" it was $300! Only $75 less than the gun cost brand new when I bought it in 2005. JMHO Link to comment Share on other sites More sharing options...
Garrison Joe, SASS #60708 Posted May 15, 2020 Share Posted May 15, 2020 5 minutes ago, Eyesa Horg said: got it back from his "specialist" it was $300! It was quite worthwhile to the feller who got paid to do that. The tools to do a nice job of forcing cone reaming don't cost that much ($300). And the labor is maybe 2 hours. Briley's of Houston only charges $95 a barrel to do that job, and they are about the best in the world! http://www.brileygunsmithing.com/c-879-full-list-of-shotgun-gunsmithing-pricing.aspx Yes, that job was "way above the normal" cost level. Good luck, GJ Link to comment Share on other sites More sharing options...
Eyesa Horg Posted May 15, 2020 Share Posted May 15, 2020 It won't happen again, that's for sure. For God knows what reason, sometimes I seem to need to learn by experience! Maybe it's the "ski" on the end of my name! Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.