Dusty Sawyer, SASS #37154 Posted January 9, 2020 Share Posted January 9, 2020 My nephew was shooting his Riverside S x S exposed hammer shotgun when suddenly it would not fire. Checking the shells revealed very light blows to the primer. First thing I noticed was that the hammer spring did not follow the hammer through total contact with the firing pin. There is .25” hammer travel between when the spring is stopped and the hammer compresses the firing pin. This is unusual from what I’ve seen on other exposed hammer guns. Looking inside, I don’t see any broken pieces. The springs are stopped by the cross pin and the hammers are then free to complete the rotation. I feel the hammers do not have enough inertia to fire the primer. But why was it working earlier? I very curious to know if this hammer free travel is normal. If anyone has experience with this Riverside shotgun, I’d appreciate hearing from you. Link to comment Share on other sites More sharing options...
Sedalia Dave Posted January 10, 2020 Share Posted January 10, 2020 How cold was it? 1 barrel or both? try with a warm gun does it still have problems? Link to comment Share on other sites More sharing options...
Dusty Sawyer, SASS #37154 Posted January 11, 2020 Author Share Posted January 11, 2020 Temperature was in the mid 40s. Strange thing was the gun shot fine for the first 4 scenarios then would not fire in either barrel. Very odd. Thanks for your reply. Link to comment Share on other sites More sharing options...
Cliff Hanger #3720LR Posted January 11, 2020 Share Posted January 11, 2020 Check to see if the receiver is closing all the way and not being held slightly open by dirt or other stuff under the barrels. THen check to see if the firing pin retaining barrels are tight. Link to comment Share on other sites More sharing options...
Sedalia Dave Posted January 11, 2020 Share Posted January 11, 2020 Bet there is a piece of lead caught in the action keeping the barrels from fully closing.. It will be very hard to see as it will be mashed very thin and the same color as everything else but I bet that is the issue. Link to comment Share on other sites More sharing options...
Doc Coles SASS 1188 Posted January 11, 2020 Share Posted January 11, 2020 Over time, the ends of the firing pins can become deformed so that the swell up and can’t go all the way forward. When this happens you start to get light primer strikes. Pull the pins and measure them to see if they are mushroomed. If they are, it’s best to replace them, but failing that you can stone them to get rid of the swelling. I have had to do this on several guns. Link to comment Share on other sites More sharing options...
Nate Kiowa Jones #6765 Posted January 11, 2020 Share Posted January 11, 2020 On 1/9/2020 at 4:35 PM, Dusty Sawyer, SASS #37154 said: My nephew was shooting his Riverside S x S exposed hammer shotgun when suddenly it would not fire. Checking the shells revealed very light blows to the primer. First thing I noticed was that the hammer spring did not follow the hammer through total contact with the firing pin. There is .25” hammer travel between when the spring is stopped and the hammer compresses the firing pin. This is unusual from what I’ve seen on other exposed hammer guns. Looking inside, I don’t see any broken pieces. The springs are stopped by the cross pin and the hammers are then free to complete the rotation. I feel the hammers do not have enough inertia to fire the primer. But why was it working earlier? I very curious to know if this hammer free travel is normal. If anyone has experience with this Riverside shotgun, I’d appreciate hearing from you. No, not unusual. Your gun has rebounding hammers. Very common on period hammer SXS's. The design allows the hammers to go fully forward as long as the trigger is pulled. But they do rebound back to a safety notch once the trigger is released. If the hammers didn't rebound they would hold the firing pin into the primers binding the action from opening. You need to know if you have enough firing pin protrusion. Action open/unloaded, while pulling the trigger lower the hammer and push it into the firing pin. The pin should protrude from the breech face at least .040' to .050". If they do, you may have loose barrels, IOW off face. Or, it could be your ammo. If you are reloading a common mistake is to over seat the primers con-caving the base of the hull. Now the primer sets too far from the pin. Same thing as off face or excessing headspace. Link to comment Share on other sites More sharing options...
The Original Lumpy Gritz Posted January 11, 2020 Share Posted January 11, 2020 OP, was the ammo factory or reloads? If factory, what brand? Hope you ain't using the all plastic hull brand. OLG Link to comment Share on other sites More sharing options...
Jack Hawkens #45246 Posted January 11, 2020 Share Posted January 11, 2020 My Riverside hammer double gun works just like Nate described. Perfectly normal. Link to comment Share on other sites More sharing options...
Bailey Creek,5759 Posted January 12, 2020 Share Posted January 12, 2020 I was having a problem with a double barrel I have. Took it to a gun smith , he told me to use only Winchester Primers. I have done that and haven't had any problems. Link to comment Share on other sites More sharing options...
Dusty Sawyer, SASS #37154 Posted January 16, 2020 Author Share Posted January 16, 2020 Thanks for all the ideas to check. I checked the action fitup and all looks good. Barrels are closing tightly. Ends of the firing pin have not mushroomed. Pins fit through the backstop with no binding. I measured the firing pin protrusion at .08” on both barrels. One thing I did notice is there is considerable play in the hammers with the firing spring fully extended and the hammer engaged against the safety notch. In other words I can freely rock the hammer back and forth between contact with the spring guide tip and the safety notch. I do not see this same play on my own Stevens SXS. Maybe the tips on the spring guide are just worn short? I will look into the ammo which were reloads. Not sure which primer was used in the reloads. thanks again Pards Link to comment Share on other sites More sharing options...
The Original Lumpy Gritz Posted January 17, 2020 Share Posted January 17, 2020 22 hours ago, Dusty Sawyer, SASS #37154 said: Thanks for all the ideas to check. I checked the action fitup and all looks good. Barrels are closing tightly. Ends of the firing pin have not mushroomed. Pins fit through the backstop with no binding. I measured the firing pin protrusion at .08” on both barrels. One thing I did notice is there is considerable play in the hammers with the firing spring fully extended and the hammer engaged against the safety notch. In other words I can freely rock the hammer back and forth between contact with the spring guide tip and the safety notch. I do not see this same play on my own Stevens SXS. Maybe the tips on the spring guide are just worn short? I will look into the ammo which were reloads. Not sure which primer was used in the reloads. thanks again Pards Get a couple bxs of factory Trap loads and give'em a try. Anytime you have a FTF with reloads. Test with factory ammo. OLG Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.