Jump to content
SASS Wire Forum

Kananaskis Kid, SASS #62402

Territorial Governors
  • Content Count

    93
  • Joined

  • Last visited

Community Reputation

7 Neutral

About Kananaskis Kid, SASS #62402

  • Rank
    Territorial Governor

Previous Fields

  • SASS #
    #62402L
  • SASS Affiliated Club
    Valley Regulators, Courtenay, B.C.

Contact Methods

  • Website URL
    http://
  • ICQ
    0

Profile Information

  • Gender
    Male
  • Location
    Campbell River, B.C. via Pincher Creek, Alta.
  • Interests
    Sports, Shooting, Model Railroading

Recent Profile Visitors

2,445 profile views
  1. We'll be there to shoot with you, the weekend before the Nationals, Jabez.
  2. Lipseys did a special run of "new" Vaqueros about 5 years ago - longest barrel length 4 5/8". I managed to get a pair of stainless steel, consecutively numbered from Long Hunter. Had to import them into Canada. Managed to get an extra set of .44 Spl cylinders from Ruger's Canadian service centre which I had reemed out for .44-40. Pretty much shoot them exclusively now.

    Now I know there has been a lot of dialogue about the rim diameter of the .44-40 cartridge, but it hasn't been a factor with my guns.  Cylinders were reamed with a new Mason reamer and throats were sized for .429 bullets.  Now, ifhtis can be accomplished by a gunsmith using a Ruger cylinder and a Mason reamer, Ruger should be able to produce a New Vaqueros in .44-40.  Just say'n.

    1. Three Foot Johnson

      Three Foot Johnson

      I have 3 of the Lipsey's .44 specials, stainless, 4 5/8", two of them with consecutive numbers, and shoot them more often than most of my CAS guns. There were 503 of these made. Similar numbers were also made in blued versions, as well as Sheriff's model configs, both blue and stainless. It would be pretty neat to have .44-40 cylinders for them too. I've got a similar set of original model 5 1/2" .38-40/.40 S&W Vaquero convertibles, two of the three being consecutive. It would be very, very cool to have a .38-40 chambered New Vaquero.

    2. Kananaskis Kid, SASS #62402

      Kananaskis Kid, SASS #62402

      If it works for .44-40, should work for .38-40.  If Lipseys or Talo could get Ruger to do a limited run of .44-40/.44 Spl and .38-40/.40S&W, I'm sure there would be a demand.

  3. Larsen,

    When Lipseys had a special run of New Vaqueros in .44 Spl, I purchased a set of stainless steel from Long Hunter.  Now, I've always wanted to shoot .44-40 and planned to have custom cylinders made by Gary Reeder, but I decided to check with the Ruger service centre here in Canada to see if I could get another set of .44 Spl cylinders from them.  I could so I bought a pair which they fit to my guns.  After I got them guns with their new cylinders back, I sent them to a gunsmith I know who reamed them out for .44-40.  Now I can shoot either caliber but for the past 3 years have exclusively shot .44-40.  So when Ruger says the New Vaqueros can't be chambered for .44-40, they aren't correct.

    Kananaskis Kid

    1. Show previous comments  1 more
    2. Kananaskis Kid, SASS #62402

      Kananaskis Kid, SASS #62402

      I'm not sure which brand of .44-40 brass has the maximum size rim, but every brand of .44-40 brass I use fits; I use Winchester and Starline most.  Every part of my guns was made by Ruger, the only "customization" was the reaming out of a New Vaquero .44 Spl cylinder to .44-40.  There isn't a lot of space between the cartridge rims, but they don't touch; everything loads smoothly.

    3. Larsen E. Pettifogger, SASS #32933

      Larsen E. Pettifogger, SASS #32933

      Again, no brand has the maximum size rim by design.  It is a matter of tolerance stacking and tool wear.  I have several .44-40 guns and ammo from one won't necessarily work in another depending on the bullet OD and case brand used.  I have standardized on the original bullet size of .427.  This fits all of my current guns.  I have .44-40s that vary from .423 to .432.  In the old days SAAMI did not exist so the dimensions for the chambers and cases were/are not uniform.  I have had the worse luck with Remington and CBC.  Both of those frequently have rims that won't fit in some of my guns or stick in the shell plates on my reloading presses.  So, I now only use Winchester or Starline brass.  They have the thinnest case necks and seem relatively consistent for rim size.  As an example, suppose the reamer your smith used was towards the maximum.  That would allow the cases to move outward from the centerline and give the rims a tiny bit more space.  A tighter chamber with wider rims and they would be a no go.

    4. Kananaskis Kid, SASS #62402

      Kananaskis Kid, SASS #62402

      The reamer used by my gunsmith was a new one from Mason, one for which I paid half.  So maybe the chambers were more toward the maximum.  All the bullets I load are .429 RNFP, usually as I previously mentioned, in Winchester or Starline brass.  Use these rounds in my Rugers as well as my Marlin Cowboy Limited and new Winchester from Miroku.  Love the .44-40.

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.