Rootin Tootin
-
Posts
1,037 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Everything posted by Rootin Tootin
-
Hey Boom Pop, If you have Charles Daley shotguns I have a bunch of Charles Daley 306 parts from a gun that I parted out. See the pics. I have a stock with a couple of cracks at the wrist but could be dilled and pinned with a dole rod. The beaver tail and locking mech is good. and the barrels are great. All parts plus barrel and beaver tail $200 and stock is free.
Or $75 for receiver parts and $125 for Beaver Tail and Barrels and I'll toss the stock in for free.
.plus shipping
Any interest
-
John, If he doesn't buy, I'm interested. Is it Satin Or Blued. Thanks RT
-
Jack, is it Satin or blued. Do you have pics. Thanks RT
-
Moses, just saw your post. I'll shipp for $115. Thanks RT
-
I have one set of checkered Eagle Micarta (Black) GF grips to fit OMV $125 shipped
Thanks... RT
-
OK Kd. I have Pay Pal prluckyy299@aol.com
or
PMO to
Paul Reinartz
6153 Christie CT
Davenport, IA 52807
-
Scissors, Pics sent. Also, I need to know the prefix on your guns. I have barrels for NMV and OMV. Want to be sure you get the correct barrels. OMV have 2 numbers and NNV have 3 Thanks RT
-
Hey John. Thanks. PMO or PayPal prlucky299@aol.com
Paul Reinartz
6153 Christie C
Davenport, IA 52807
563 349 2273
-
Hey Randy. Rootin Tootin here. I saw your post about a lever lock to help prevent jacking a live round. I'm planning on getting one but want to know with it installed how do you show clear at the unloading table with the lock installed without pulling the trigger? The only way I can see to do it is to pull the trigger and gradually lower the hammer and cycle it then.
Thanks. RT
- Show previous comments 2 more
-
Hope so too, it is a little harder to put the rifle back together but not bad. I install the right links, right side plate then roll it over and drop in the lever lock and left side links. I have a short punch approximately the same diameter at the side plate screw I stick through the hole in the right side plate and through the lever lock. Then I install the left side plate and push the punch through the hole, now I can put the screw on the end of the punch and push the punch back out to help me keep the screw aligned. I hope that made sense? It is actually pretty easy once I got used to it.
If it doesn't make sense I can make a video and send it.
Randy
-
I have a spoked wheel for $25 plus 10 for shipping. I replaced my wheels last year for both the plastic versions but saved the one spoked wheel for just this occassion. RT
-
I have a forend if you are still looking for a 20 inch with an Octagon barrel. RT
-
Any interest in the parts or the entire Charles Dailey after you viewed the pics.
-
OK Buddy.
Paul Reinartz
6153 Christie Ct
Davenport, IA 52807
Send me your info so I can send the bolt. Thanks RT
-
OK Copperhead. Thanks
Paul Reinartz
6153 Christie Ct
Davenport, IA 52807
My e mail is prlucky299@aol.com phone 563 349 2273
so send me your address so I ca send the bolt.
-
Snake Oil George contact info is 918-729-0430. he turned mine around in 3 weeks. Enjoy RT
-
Scarlett, I bought some Clean Shot from you in TN 2 years ago. Do you still have some in inventory. I'd like to buy 10 or 15 lbs. Good stuff... Thanks Rootin Tootin 21707
-
Hey Flat Top. Rootin Tootin (21707) here. I sent my registration in with three of my friends that arrived with you folks on Tuesday or Wednesday. My 3 friend, Badlands Charlie, Wicker Nash, and Popcorn Kelly all have received confirmation on their entries, but I have heard nothing. So I filled out an online registration to be sure I get in. I'm not sure what happened to the first one, so you may see I'm registered twice at some point and give me a refund. My check hasn't cleared yet so I'm guessing you lost the first one or maybe things are so hectic that you just haven't got to it yet. Either way I want to be sure I get in. Thanks RT