Dirty Dan Dawkins Posted February 17 Share Posted February 17 Pm me if you work on dryers. I have a hard time getting an appliance guy out here. Link to comment Share on other sites More sharing options...
sassnetguy50 Posted February 17 Share Posted February 17 You might try searching online for parts stores. They've helped me diagnose problems so they could sell me the part. Link to comment Share on other sites More sharing options...
watab kid Posted February 17 Share Posted February 17 i did the on-line bit and got about three extra years out of my old dryer , its not really hard but in some ways its a PITA Link to comment Share on other sites More sharing options...
Chicago kidd Posted February 17 Share Posted February 17 My dryer wouldnt heat it would go on then shut off did a youtube search found out it was an 12.00 fuse saved a ton of money so try yourube Link to comment Share on other sites More sharing options...
Colorado Coffinmaker Posted February 17 Share Posted February 17 Absolutely. I use my package truck to load the recalcitrant dryer to the Tree Lawn day before trash day. Someone always drives by and hauls it away and I go get a really nice NEW DRYER!! Which, incidentally, Lowes DELIVERS!! Link to comment Share on other sites More sharing options...
Texas Joker Posted February 17 Share Posted February 17 https://www.repairclinic.com What's wrong? Link to comment Share on other sites More sharing options...
Dirty Dan Dawkins Posted February 18 Author Share Posted February 18 Figured it out with some thanks owed to Assassin. Bad exhaust thermistor. $8 part Link to comment Share on other sites More sharing options...
Capt. James H. Callahan Posted February 18 Share Posted February 18 Glad it worked out for you. Some years ago I replaced the element in ours. Took me two days to get the old element out. Didn't see anyway in H*lll I could get the new one in without destroying it. Then I figured out how to pop the top off it and found the one little sheet metal screw that held all that crap inside. Spent 2-3 days on a job that would have taken about 30 min. for someone that knew how to do it. JHC Link to comment Share on other sites More sharing options...
Texas Joker Posted February 18 Share Posted February 18 The last time our dryer stopped heating my wife pointed I had had it apart 4 times since we bought it to replace various parts. She said 'it's time..' And now Lowes gets a monthly for a few at 0% Link to comment Share on other sites More sharing options...
Chantry Posted February 18 Share Posted February 18 Youtube is often a good source on how to take things apart and put them back together Link to comment Share on other sites More sharing options...
Larsen E. Pettifogger, SASS #32933 Posted February 18 Share Posted February 18 15 hours ago, Dirty Dan Dawkins said: Bad exhaust thermistor. Is that near the flux capacitor? Link to comment Share on other sites More sharing options...
Cypress Sun Posted February 18 Share Posted February 18 1 hour ago, Larsen E. Pettifogger, SASS #32933 said: Is that near the flux capacitor? Hasn't been invented yet. Link to comment Share on other sites More sharing options...
Gateway Kid SASS# 70038 Life Posted February 18 Share Posted February 18 2 hours ago, Chantry said: Youtube is often a good source on how to take things apart and put them back together Fixed it for you! Regards Gateway Kid Link to comment Share on other sites More sharing options...
Dirty Dan Dawkins Posted February 18 Author Share Posted February 18 5 hours ago, Gateway Kid SASS# 70038 Life said: Fixed it for you! Regards Gateway Kid I always have leftover screws no matter what I work on. So long as a screw is less than 1/4”, I figure it’s not holding much. If it’s a # 10 or less sheet metal screw or self-tapping screw, it’s pretty much inconsequential. Link to comment Share on other sites More sharing options...
sassnetguy50 Posted February 19 Share Posted February 19 54 minutes ago, Dirty Dan Dawkins said: I always have leftover screws no matter what I work on. So long as a screw is less than 1/4”, I figure it’s not holding much. If it’s a # 10 or less sheet metal screw or self-tapping screw, it’s pretty much inconsequential. They call that "new and improved" being eco friendly and lighter weight. Link to comment Share on other sites More sharing options...
Capt. James H. Callahan Posted February 19 Share Posted February 19 23 hours ago, Larsen E. Pettifogger, SASS #32933 said: Is that near the flux capacitor? You probably have to remove that AND the motor to get to the thermistor. JHC Link to comment Share on other sites More sharing options...
John E. Law Posted February 20 Share Posted February 20 Go on you tube and do a search on your model. You'll get something close as they're all the same inside. Very simple to work on and you can get most parts on Amazon. That's goes for most appliances except refrigerators as they have refrigerant. *Also in 99% of appliances there are the schematics and a troubleshooting manual stuffed in the back inside the unit. JEL Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.