Currahee Posted January 30, 2023 Share Posted January 30, 2023 Whaddaya hear, whaddaya say? Do they do any good? Which one do you like? Thanks, C. Link to comment Share on other sites More sharing options...
Randy Saint Eagle, SASS # 64903 Posted January 30, 2023 Share Posted January 30, 2023 Here’s my low budget version made by a friend. Link to comment Share on other sites More sharing options...
Garrison Joe, SASS #60708 Posted January 30, 2023 Share Posted January 30, 2023 Great stuff, if you need it. The combined chamber checking and resizer is the best. Keep one in my cart since I shoot a double barrel. good luck, GJ Link to comment Share on other sites More sharing options...
Cheyenne Ranger, 48747L Posted January 31, 2023 Share Posted January 31, 2023 I got in on the QuikLoader when it first came out a bit pricey but it does a great job of narrowing the crimp end by 3° https://coyotesmercantile.com/products/quikloader Link to comment Share on other sites More sharing options...
Bearfoot Tracker Posted January 31, 2023 Share Posted January 31, 2023 I have tried other people's sizers mounted on their cart but I found the SlixSprings Shotshell Checker works great for me. I was having A LOT of trouble shucking shells (AA Low Recoil / Low Noise) from my slicked up Stoeger shotgun until I started using this device. I keep it on the cart and size everything that goes into my belt before and during the match. Link to comment Share on other sites More sharing options...
Badlands Bob #61228 Posted January 31, 2023 Share Posted January 31, 2023 On 1/30/2023 at 2:05 AM, Garrison Joe, SASS #60708 said: Great stuff, if you need it. The combined chamber checking and resizer is the best. Keep one in my cart since I shoot a double barrel. good luck, GJ That's what I use. Works great. I check every shell before it goes in my belt on the stage. It has virtually eliminated sticking shells in my SxS. Link to comment Share on other sites More sharing options...
KingSnake Posted January 31, 2023 Share Posted January 31, 2023 I already have the Slix tool, so I made an end squeezer using it. Link to comment Share on other sites More sharing options...
Badlands Bob #61228 Posted January 31, 2023 Share Posted January 31, 2023 Next step is a hydraulic pump and a toggle switch. Link to comment Share on other sites More sharing options...
Cheyenne Ranger, 48747L Posted January 31, 2023 Share Posted January 31, 2023 don't forget the MEC super sizer to resize the brass at the base--helps mine fall out Link to comment Share on other sites More sharing options...
Chancy Shot, SASS #67163 Posted January 31, 2023 Share Posted January 31, 2023 13 hours ago, Cheyenne Ranger, 48747L said: I got in on the QuikLoader when it first came out a bit pricey but it does a great job of narrowing the crimp end by 3° https://coyotesmercantile.com/products/quikloader This is the one I use. I have it mounted on a drill press. I have not tried others. Chancy Link to comment Share on other sites More sharing options...
Blind Squirrel Posted January 31, 2023 Share Posted January 31, 2023 4 minutes ago, Chancy Shot, SASS #67163 said: This is the one I use. I have it mounted on a drill press. I have not tried others. Chancy What do you use to hold the shell? Link to comment Share on other sites More sharing options...
Krazy Kajun Posted January 31, 2023 Share Posted January 31, 2023 2 hours ago, Badlands Bob #61228 said: Next step is a hydraulic pump and a toggle switch. ....and remember Evil Bob....don't let the magic smoke out of the pump! Kajun Link to comment Share on other sites More sharing options...
Abilene Slim SASS 81783 Posted February 1, 2023 Share Posted February 1, 2023 12 hours ago, Blind Squirrel said: What do you use to hold the shell? I remove the crimp starter on my Mec press and mount the QuickLoader at that station. I load a bunch of shells, then use the QL for the final step. Crimp starter goes back on when finished. Takes two minutes to make the swap each time. Link to comment Share on other sites More sharing options...
watab kid Posted February 1, 2023 Share Posted February 1, 2023 i like the idea that it could become a stage on the loader adding extra stepd has always turned me off , i got rid of my mec base sizer for that reason , Link to comment Share on other sites More sharing options...
Cusz M. Dutch SASS Life 55326 Posted February 1, 2023 Share Posted February 1, 2023 a rolled crimp will do the same for reloads Link to comment Share on other sites More sharing options...
Yusta B. Posted February 1, 2023 Share Posted February 1, 2023 On 1/31/2023 at 9:42 AM, Blind Squirrel said: What do you use to hold the shell? I have a different type & mount it in an old Lee Classic Turret press. It uses an RCBS 12 ga shell holder. Could use a single stage press too. Link to comment Share on other sites More sharing options...
Randy Saint Eagle, SASS # 64903 Posted February 1, 2023 Share Posted February 1, 2023 On 1/31/2023 at 10:58 AM, Krazy Kajun said: ....and remember Evil Bob....don't let the magic smoke out of the pump! Kajun I worked in maintenance in a factory for 22 years and learned that virtually all equipment runs on smoke, if you let the smoke out it won’t run! Randy Link to comment Share on other sites More sharing options...
Krazy Kajun Posted February 1, 2023 Share Posted February 1, 2023 1 hour ago, Randy Saint Eagle, SASS # 64903 said: I worked in maintenance in a factory for 22 years and learned that virtually all equipment runs on smoke, if you let the smoke out it won’t run! Randy Randy, fortunately I was able to advise Badlands Bob on which smoke replacement cylinder he needed to obtain! Kajun Link to comment Share on other sites More sharing options...
Sedalia Dave Posted February 1, 2023 Share Posted February 1, 2023 4 hours ago, Randy Saint Eagle, SASS # 64903 said: I worked in maintenance in a factory for 22 years and learned that virtually all equipment runs on smoke, if you let the smoke out it won’t run! Randy First day of electronics school in the Navy we learned that all electronics run on magic smoke. Link to comment Share on other sites More sharing options...
Eyesa Horg Posted February 1, 2023 Share Posted February 1, 2023 That smoke is the fastest way to find the defective component Link to comment Share on other sites More sharing options...
Colorado Coffinmaker Posted February 3, 2023 Share Posted February 3, 2023 I resolved ALL those pesky issues some time back. If you run ALL BRASS hulls, you don't need all that stuff. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.