Bisley Joe Posted May 17, 2022 Share Posted May 17, 2022 I have a pair of open top revolvers from Cimarron. They are in .45 Colt. Have been thinking of getting cylinders and barrels in .38 special. At T&C I see a .38 barrel is $150. The cylinder is $110.20. That makes for being able to shoot .45 and .38 for about $260: a lot less than another gun (but then, more guns is always better). Would have to see what it would cost to have these fitted though. Anyone done this? Worth it? Link to comment Share on other sites More sharing options...
Bisley Joe Posted May 17, 2022 Author Share Posted May 17, 2022 Forgot: Anyone know if the grips on these Open Tops will fit the Pietta 1851 Navy? I want to change the grip profile to be more accurate and maybe these are better. Link to comment Share on other sites More sharing options...
Prairie Dawg, SASS #50329 Posted May 17, 2022 Share Posted May 17, 2022 Open tops are made by Uberti. Uberti & Pietta grips do not interchange without working on them. When I started, I had Open Tops with 44 cylinders & barrels and 38 cylinders & barrels I had them in 5" and 7.5" lengths. Loved the versatility -- I could switch back and forth at will, and they dropped right in. They handle just like cap guns. I still have three 44s with 7-1/2" barrels, one 5" barrel, and a 3" barrel And, one 45 with a 7-1/2' barrel and a 3" snubbie barrel. Larsen E. Pettifogger wrote an article that includes changing the grip profile, if I remember correctly I believe I have a copy of it in my files -- If I do, I'll send it to you (PM me your email address) --Dawg Link to comment Share on other sites More sharing options...
Bisley Joe Posted May 18, 2022 Author Share Posted May 18, 2022 3 hours ago, Prairie Dawg, SASS #50329 said: Open tops are made by Uberti. Uberti & Pietta grips do not interchange without working on them. When I started, I had Open Tops with 44 cylinders & barrels and 38 cylinders & barrels I had them in 5" and 7.5" lengths. Loved the versatility -- I could switch back and forth at will, and they dropped right in. They handle just like cap guns. I still have three 44s with 7-1/2" barrels, one 5" barrel, and a 3" barrel And, one 45 with a 7-1/2' barrel and a 3" snubbie barrel. Larsen E. Pettifogger wrote an article that includes changing the grip profile, if I remember correctly I believe I have a copy of it in my files -- If I do, I'll send it to you (PM me your email address) --Dawg Prairie Dawg, did you have to get the guns worked on by a gunsmith for the different caliber cylinders/barrels, or did they work fine by just popping them on? Link to comment Share on other sites More sharing options...
smokedawg SASS#60968 Posted May 18, 2022 Share Posted May 18, 2022 tag for info on this. Link to comment Share on other sites More sharing options...
Prairie Dawg, SASS #50329 Posted May 18, 2022 Share Posted May 18, 2022 1 hour ago, Bisley Joe said: Prairie Dawg, did you have to get the guns worked on by a gunsmith for the different caliber cylinders/barrels, or did they work fine by just popping them on? They just fit right on. This was a selling point of these revolvers back then. I don't think they even advertise them anymore. So, I don't know if they still swap out so easily. A while back, I tried to put a 44 barrel on my 45 frame, & it wouldn't index properly. And one of the 44 barrels wouldn't go on either, so I would need to have a gunsmith do some fitting if I wanted to have one frame & multiple cylinders/barrels --Dawg Link to comment Share on other sites More sharing options...
Bisley Joe Posted May 18, 2022 Author Share Posted May 18, 2022 3 hours ago, Prairie Dawg, SASS #50329 said: They just fit right on. This was a selling point of these revolvers back then. I don't think they even advertise them anymore. So, I don't know if they still swap out so easily. A while back, I tried to put a 44 barrel on my 45 frame, & it wouldn't index properly. And one of the 44 barrels wouldn't go on either, so I would need to have a gunsmith do some fitting if I wanted to have one frame & multiple cylinders/barrels --Dawg I'll check it out regarding mine. Thank you. Link to comment Share on other sites More sharing options...
Doc Nelson #19958 Posted May 18, 2022 Share Posted May 18, 2022 I had zero issues going from .38 to .44 spl. Other than waiting for years to get the .44 spl. parts. Doc Nelson Link to comment Share on other sites More sharing options...
Rye Miles #13621 Posted May 18, 2022 Share Posted May 18, 2022 Just buy a pair of Smoke Wagons in .38/.357 and be done with it! You won't be sorry! Link to comment Share on other sites More sharing options...
Colorado Coffinmaker Posted May 18, 2022 Share Posted May 18, 2022 Bisley Joe, In the past, ALL the barrel/cylinder combinations for the Open Top would interchange. The only problem was the abysmal Barrel to Arbor fit which needed correction. They still need the Barrel to Arbor fit corrected. There are two way to do it. Cheap, quick and simple is to drop a #10 Split washer down the barrel bore, re-assemble and re-Fit the wedge. The washer has to be used with each different barrel. More involved method requires some machine work to the arbor with a permanent spacer. Check Pettifogger's tutorial for this fix. Uberti often changes little dimensions between production runs. It may require some minor fitting to change calibers. My personal guns have 45 Schofield Cylinders/Barrels, 44 Colt Cylinders/Barrels and .38 Special Cylinders/Barrels. I can change cartridges in about 10 minutes for both guns. I don't necessarily like running 45 Colt in the Open Top Cylinder as the chamber walls are quite thin. The 45s use to have a habit of spitting out the little bit of metal in the bottom of the cylinder bolt notch. Link to comment Share on other sites More sharing options...
Ninety Caliber Al, 50218 Posted May 18, 2022 Share Posted May 18, 2022 I have a set of 1872 Open Tops in .38 special that I converted to snubbies with a couple of 3 1/2” bbl.’s I got from Colorado Coffinmaker. With a little instruction from him I fitted them myself ! Link to comment Share on other sites More sharing options...
Rye Miles #13621 Posted May 18, 2022 Share Posted May 18, 2022 3 hours ago, Rye Miles #13621 said: Just buy a pair of Smoke Wagons in .38/.357 and be done with it! You won't be sorry! I just re-read the OP and I see you're a open top fan. (Ignore my Smoke Wagon comment above) I would just buy a new pair of open tops in .38, always fun to buy new guns!! Link to comment Share on other sites More sharing options...
Colorado Coffinmaker Posted May 19, 2022 Share Posted May 19, 2022 Now that there solution from Rye is just the ticket!! Double yer pleasure - Double yer Fun (stolen famous commercial line) Link to comment Share on other sites More sharing options...
Bisley Joe Posted May 21, 2022 Author Share Posted May 21, 2022 Thanks everyone so far for all the great information. I am looking at replacement barrels and cylinders, but am also tempted towards .38 conversions. Link to comment Share on other sites More sharing options...
H. K. Uriah, SASS #74619 Posted May 22, 2022 Share Posted May 22, 2022 Wouldn't it be easier to get a pair already in .38? If you don't wanna keep the .45's, use 'em for trade in and save some money that way. Or keep them and then you have the option of either/or. Link to comment Share on other sites More sharing options...
watab kid Posted May 22, 2022 Share Posted May 22, 2022 my thy thoughts as well , but im not in the market for something like this nor considering such a conversion , i guess there might be a good reason , Link to comment Share on other sites More sharing options...
smokedawg SASS#60968 Posted May 22, 2022 Share Posted May 22, 2022 T&C ? I'm not familiar with this vendor? Link to comment Share on other sites More sharing options...
Griff Posted May 22, 2022 Share Posted May 22, 2022 Hmmm... going from .45s to .38s... is kinda gamey... leaves me wonderin' how long it'll be before you're shootin' two-handed? Link to comment Share on other sites More sharing options...
smokedawg SASS#60968 Posted May 22, 2022 Share Posted May 22, 2022 Duh!!.....T&C=Taylor and Company. I checked their site and the only barrel I found was $192 plus shipping. Where is the $150 one? Link to comment Share on other sites More sharing options...
Bisley Joe Posted May 22, 2022 Author Share Posted May 22, 2022 13 hours ago, H. K. Uriah, SASS #74619 said: Wouldn't it be easier to get a pair already in .38? If you don't wanna keep the .45's, use 'em for trade in and save some money that way. Or keep them and then you have the option of either/or. Yeah that's an option. A new open top in .38 would be about $550. A barrel and cylinder would be about half that. However, what I am leaning more towards is an 1851 Navy Richards-Mason Conversion. Then I would have a pair of 1851 Navies in C&B, and a pair in .38. Fun all around. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.