Prairie Dawg, SASS #50329 Posted May 16, 2022 Share Posted May 16, 2022 SOLD -- THANKS Good Evening: I have for sale 2 sets of Ruger Logo Black Checkered Polymer Grips. They came on a pair of Old Army revolvers that I purchased. They are a bit small for the XR3-RED gripframe, but they worked. I swapped them out for two sets of Eagle checkered GF grips. I'm not quite sure which model of Rugers they fit, as I am not a Ruger-guy, except for Old Armies. But, if you are, you can see from they pics if they will work for you. $100 shipped for the pair. Paypal & personal check OK PM with questions. Thanks for looking --Dawg Link to comment Share on other sites More sharing options...
Moe T Vator Posted May 16, 2022 Share Posted May 16, 2022 Howdy Dawg, Just to clarify, these do fit the ROA or were too small? Thanks! Link to comment Share on other sites More sharing options...
Prairie Dawg, SASS #50329 Posted May 16, 2022 Author Share Posted May 16, 2022 17 minutes ago, Moe T Vator said: Howdy Dawg, Just to clarify, these do fit the ROA or were too small? Thanks! They were a bit small. They weren't as tight as an old model Vaquero grip, and a bit of the side of the backstrap was showing. I can photograph it if you like. The pard from whom I purchased the ROAs from had been using them, but I like the better fit of the eagle GF grips. Please let me know Thanks --Dawg Link to comment Share on other sites More sharing options...
Moe T Vator Posted May 16, 2022 Share Posted May 16, 2022 copy, my plan would be to put them on the ROAs. if you have a pic with them on yours that would be great for reference! TY- MTV Link to comment Share on other sites More sharing options...
Prairie Dawg, SASS #50329 Posted May 16, 2022 Author Share Posted May 16, 2022 Moe: You will notice in the images, a small part of the side of the backstrap is showing, there is a bit larger gap at the back of the triggerguard, and a bit of the side of the triggerguard can be seen as you look down the inside of the curve toward the bottom of the grip. Also, there is a bit of grip extension at the bottom of the grip. These grip panels give your hand a solid grip on the ROA, but the fit could be better. Hope this helps. Thanks --Dawg Link to comment Share on other sites More sharing options...
Moe T Vator Posted May 16, 2022 Share Posted May 16, 2022 thank you sir. Link to comment Share on other sites More sharing options...
Springfield Slim SASS #24733 Posted May 16, 2022 Share Posted May 16, 2022 They are probably the newer XR-3 grips going by the chart I was just looking at. Slightly smaller than XR3-Red. Just compared my ROA to the kids' 3 screw Single Sixes, looks like they might fit except the locating pin hole is a bit higher. Link to comment Share on other sites More sharing options...
Prairie Dawg, SASS #50329 Posted May 16, 2022 Author Share Posted May 16, 2022 Thanks Slim: Not being a Ruger-Guy, I don't have a gun to try them on. I'll bring them to a shoot, & see if I can borrow one to see if they fit. --Dawg Link to comment Share on other sites More sharing options...
Shorty Jenkins SASS#46533 Posted May 19, 2022 Share Posted May 19, 2022 My old friend, Just ran on to this post. I use these on several of my Rugers. Absolutely crazy about them. Would love to have these, but a little tight right now with other life necessities. They were factory on New Model, Fixed sight Singles Sixes in the late 90's and early 2000's. Maybe I could trade you out of them someway. Hope you are fine and the family all well. We are still "guarding the river" down here in Adams County. Just getting old and feeble. Anyway, always good to hear from you mi amigo! Adios, Shorty Link to comment Share on other sites More sharing options...
Prairie Dawg, SASS #50329 Posted May 19, 2022 Author Share Posted May 19, 2022 Sold to Shorty -- THANKS Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.