July Smith Posted October 14, 2021 Share Posted October 14, 2021 I typically shoot Frontiersman with a pair of 36cal Uberti 1851s. Last few monthlies I had a few stages were the load levers fell binding the cylinder and killing my times. I load on the gun and suspect over the last few years the latches are a little more worn than when I first started. I have tried tying the levers up with thin strips of leather, but this causes issues when it comes to reloading and re-holstering. I've tried refiling the latch parts but I still get at least one drop per match. I am tempted to find some small pipe clamps to wrap around the barrel and load lever but suspect I'll have the same issue that I had with the leather strips. Any other Frontiersman have a better fix for this problem? Link to comment Share on other sites More sharing options...
Captain Bill Burt Posted October 14, 2021 Share Posted October 14, 2021 Could you load off the gun and just take the lever off? I'm curious, cause I'll be shooting my 1851s for the first time in the BP match at the SE Regional. Hopefully I won't have that issue. Link to comment Share on other sites More sharing options...
July Smith Posted October 14, 2021 Author Share Posted October 14, 2021 7 minutes ago, Captain Bill Burt said: Could you load off the gun and just take the lever off? I'm curious, cause I'll be shooting my 1851s for the first time in the BP match at the SE Regional. Hopefully I won't have that issue. Yes, but loading off the gun is a PITA and takes me much more time. I know guys with Rugers and Remingtons that can load off the gun efficiently, but for me driving out the wedge and reinstalling it takes too long. Link to comment Share on other sites More sharing options...
Branchwater Jack SASS #88854 Posted October 14, 2021 Share Posted October 14, 2021 tie a piece of string around the barrel and lever. Roll the string off the end of the barrel when you want to load. Roll the string back over to keep the barrel in place. Link to comment Share on other sites More sharing options...
Captain Bill Burt Posted October 14, 2021 Share Posted October 14, 2021 Maybe put in a stronger spring or replace that "plunger" part? Link to comment Share on other sites More sharing options...
Branchwater Jack SASS #88854 Posted October 14, 2021 Share Posted October 14, 2021 I have also previously used rubber O rings in place of the string.... Link to comment Share on other sites More sharing options...
Crazy Gun Barney, SASS #2428 Posted October 14, 2021 Share Posted October 14, 2021 Here is an out of the box thought. remove the loading lever screw and replace it with a removable pin. This may require drilling the holes in the frame as well as the hole in the loading lever. To load it, put the lever in place and put the pin in the hole. When done loading, pull the pin and drop the loading lever back in your cart. Or, instead of a removable pin, perhaps you can find a screw with a knurled head allowing you to quickly and easily remove it for shooting. Just a thought. Not sure if this would qualify as an "unauthorized modification". Link to comment Share on other sites More sharing options...
Abilene Slim SASS 81783 Posted October 14, 2021 Share Posted October 14, 2021 I had that problem once and found that the levers weren’t latching completely. They had acquired a slight bend with repeated use thru the years. Full disclosure - I had been using a cheater bar as these are sheriff models with that too-short lever. I straightened them but am now loading off the gun. It doesn’t take me any longer to do it that way. Link to comment Share on other sites More sharing options...
Crazy Gun Barney, SASS #2428 Posted October 14, 2021 Share Posted October 14, 2021 Or... might try a stronger spring in the latch at the end of the handle.... as Capt Bill Burt suggested. Link to comment Share on other sites More sharing options...
Garrison Joe, SASS #60708 Posted October 14, 2021 Share Posted October 14, 2021 If you want to see what a stronger latch spring would do, drop a small steel ball down the latch mounting hole under the spring. That will increase spring pressure temporarily, to see if that helps out. Make sure it's small as the spring or slightly smaller (so it won't get stuck at the bottom). If adventurous, you could also (cold) peen the latching bar to stretch it 10 to 20 thousandths. good luck, GJ Link to comment Share on other sites More sharing options...
Kid Rich Posted October 14, 2021 Share Posted October 14, 2021 Use a larger granulation of powder. 2f instead of 3f or 1f instead of 2f. My Walkers will drop the lever with a full load of 3f but not with the same load of 2f. kR PS you could even go with Schuetzen Harzer which is reenactor powder and more coarse than 1f. Link to comment Share on other sites More sharing options...
Doc Coles SASS 1188 Posted October 15, 2021 Share Posted October 15, 2021 I had a friend who had this problem with his walkers, which have a much weaker latching system. He worked in a lab that had a machine for magnetizing steel. He used it to make the levers strongly magnetic, and no more falling loading levers. I thought that was a neat trick. In your case, I would inspect the latching surfaces (the lug on the bottom of the barrel and the latch piece in the end of the lever) and replace them if they show any wear. Link to comment Share on other sites More sharing options...
Tequila Shooter Posted October 15, 2021 Share Posted October 15, 2021 I had the loading lever latch fall off during a match, now I carry a pipe cleaner with me. The wire is thin enough to get a good tight twist and the cover prevents metal to metal contact. It’s only a temporary fix, but it saved my bacon and I even gave one to another shooter who was having the same issue as you. Link to comment Share on other sites More sharing options...
Colorado Coffinmaker Posted October 15, 2021 Share Posted October 15, 2021 CONSIDER: Attacking the "Latch" and the barrel Stud with sharp tools is only going to open the distance the latch has to travel, making the problem worse. SUGGEST: Replace the latch, inspect and replace the barrel stud if needed. Also, determine if the loading arm is indeed straight. Link to comment Share on other sites More sharing options...
Castalia,SASS#18915 Posted October 15, 2021 Share Posted October 15, 2021 Used a rubber band on my Walker. Worked well and was not in the way of the sights. Link to comment Share on other sites More sharing options...
El Sobrante Kid Posted October 16, 2021 Share Posted October 16, 2021 If you can't find a mechanical solution, go with Castalia's suggestion, Rubber bands were first patented in the mid-1800's, and are period correct. https://en.wikipedia.org/wiki/Rubber_band Link to comment Share on other sites More sharing options...
Abilene Slim SASS 81783 Posted October 16, 2021 Share Posted October 16, 2021 6 hours ago, Colorado Coffinmaker said: CONSIDER: Attacking the "Latch" and the barrel Stud with sharp tools is only going to open the distance the latch has to travel, making the problem worse. SUGGEST: Replace the latch, inspect and replace the barrel stud if needed. Also, determine if the loading arm is indeed straight. This. Link to comment Share on other sites More sharing options...
PaleWolf Brunelle, #2495L Posted October 16, 2021 Share Posted October 16, 2021 On 10/14/2021 at 11:51 AM, Crazy Gun Barney, SASS #2428 said: Or, instead of a removable pin, perhaps you can find a screw with a knurled head allowing you to quickly and easily remove it for shooting. Just a thought. Not sure if this would qualify as an "unauthorized modification". It would....HOWEVER! A set screw (requiring a hex wrench) is an approved modification for Walkers (REF: SHB p.36) This method has also been approved: Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.