Chantry Posted May 3, 2021 Share Posted May 3, 2021 Most of us have at least one gun that we tried to dissemble and reassemble that caused us to say many bad words that are not allowed in the Saloon. What are some of your least favorite guns to take apart? I'm not talking about full disassembly where the entire gun is taken apart, but more than just a basic field strip. Ruger Redhawk, took it apart to swap out the hammer spring. I don't remember the details, but it took me 2 hours to put it back together. Winchester 1894, another gun that took forever to put back together. Colt 1903 Pocket Hammerless, one of my favorite guns and JMB is without a freaking genius when it comes to designing guns. The gun comes apart with just two hands, but it takes three hands (or a vice) to put it back together again. I'm sure someone will mention the Ruger MkI/II/III and sometimes getting the main spring housing back in can be a pain, but I've found it gets easier the more the gun is used. Taking a Luger or Mauser Broomhandle apart is far easier than the first three guns I mentioned, while the internals are far more complicated, the guns will only go back together the correct way or not all, there isn't an in between. Link to comment Share on other sites More sharing options...
DeaconKC Posted May 3, 2021 Share Posted May 3, 2021 2 minutes ago, Chantry said: Most of us have at least one gun that we tried to dissemble and reassemble that caused us to say many bad words that are not allowed in the Saloon. What are some of your least favorite guns to take apart? I'm not talking about full disassembly where the entire gun is taken apart, but more than just a basic field strip. Ruger Redhawk, took it apart to swap out the hammer spring. I don't remember the details, but it took me 2 hours to put it back together. Winchester 1894, another gun that took forever to put back together. Colt 1903 Pocket Hammerless, one of my favorite guns and JMB is without a freaking genius when it comes to designing guns. The gun comes apart with just two hands, but it takes three hands (or a vice) to put it back together again. I'm sure someone will mention the Ruger MkI/II/III and sometimes getting the main spring housing back in can be a pain, but I've found it gets easier the more the gun is used. Taking a Luger or Mauser Broomhandle apart is far easier than the first three guns I mentioned, while the internals are far more complicated, the guns will only go back together the correct way or not all, there isn't an in between. The 1903 Colt? EGADS! You are correct. Link to comment Share on other sites More sharing options...
Okie Sawbones, SASS #77381 Posted May 3, 2021 Share Posted May 3, 2021 Illudium Q-36 Explosive Space Modulator Link to comment Share on other sites More sharing options...
Chantry Posted May 3, 2021 Author Share Posted May 3, 2021 I'll add a gun I will never do more then field strip: H&K P7M8 (and any of it's variants). I took the grip panels off, looked at all the little parts and springs under the grip panels, put the grip panels back on and promised myself that I would NEVER attempt anything more than field stripping the gun. Link to comment Share on other sites More sharing options...
Warden Callaway Posted May 3, 2021 Share Posted May 3, 2021 43 minutes ago, Chantry said: Most of us have at least one gun that we tried to dissemble and reassemble that caused us to say many bad words that are not allowed in the Saloon. What are some of your least favorite guns to take apart? I'm not talking about full disassembly where the entire gun is taken apart, but more than just a basic field strip. Ruger Redhawk, took it apart to swap out the hammer spring. I don't remember the details, but it took me 2 hours to put it back together. Winchester 1894, another gun that took forever to put back together. Colt 1903 Pocket Hammerless, one of my favorite guns and JMB is without a freaking genius when it comes to designing guns. The gun comes apart with just two hands, but it takes three hands (or a vice) to put it back together again. I'm sure someone will mention the Ruger MkI/II/III and sometimes getting the main spring housing back in can be a pain, but I've found it gets easier the more the gun is used. Taking a Luger or Mauser Broomhandle apart is far easier than the first three guns I mentioned, while the internals are far more complicated, the guns will only go back together the correct way or not all, there isn't an in between. Many years ago I learned to hate guns that were pinned together and held multiple parts and springs. Link to comment Share on other sites More sharing options...
Rye Miles #13621 Posted May 3, 2021 Share Posted May 3, 2021 I had a heckuva time with a Ruger 22/45 some years ago. I couldn’t get the darn thing back together right, it took me forever !!! Link to comment Share on other sites More sharing options...
Finagler 6853 Life Posted May 3, 2021 Share Posted May 3, 2021 I opened the side plate of a S&W 29 once. After looking inside I slowly and quietly put the side plate back on swearing to myself to never do that again. I watched a video of a "smith" taking apart a Winchester 74, semi auto .22. With all the warnings about this spring and that lever, I decided I would just bathe it in cleaning solution so I wouldn't have to take it apart. I had a picture of my 73 totally stripped down on my bench as my phone front page. Amazing all the little tiny parts, screws and springs that go into that thing. I am amazed at how something that looks so delicate can be so powerful. I guess if I can strip that down and get it back together I could do a 29 and the 74 but why push my luck. Link to comment Share on other sites More sharing options...
Eyesa Horg Posted May 3, 2021 Share Posted May 3, 2021 Was going to disassemble a Browning BLR in 308 for a buddy as there was some rust showing. Read up on it and declined. Apparently getting the gear back right is a nightmare. Link to comment Share on other sites More sharing options...
John Kloehr Posted May 3, 2021 Share Posted May 3, 2021 The Sig SP2022 has several backstraps (grips) to better fit a particular shooter's hand. I did change mine to fit me better. There is an amazing amount of hardware hidden between the grip and the mag well, I did not even think about trying to figure out what all those parts do, and plan to never take any of it apart. Link to comment Share on other sites More sharing options...
Crooked River Pete, SASS 43485 Posted May 3, 2021 Share Posted May 3, 2021 Remington nylon 66 Link to comment Share on other sites More sharing options...
Pat Riot Posted May 3, 2021 Share Posted May 3, 2021 A High Standard Sentinel Mk IV. Lots of colorful language and the need of a third hand. Two guns that I am thankful I have books with disassembly / assembly instruction on, Winchester 94 and Rossi 92. By the way, I no longer have the Rossi but I do have Stevez DVD on it in case anyone ever needs it. Another gun that I no longer have that was a b**** to disassemble / reassemble was that POS Remington R51 I had. Good riddance to that piece of crap! Link to comment Share on other sites More sharing options...
Charlie Harley, #14153 Posted May 3, 2021 Share Posted May 3, 2021 2 minutes ago, Crooked River Pete, SASS 43485 said: Remington nylon 66 You were one post ahead of me. Stripped and reassembled mine once. Then settled for flushing with solvent but no taking apart. Link to comment Share on other sites More sharing options...
Crooked River Pete, SASS 43485 Posted May 3, 2021 Share Posted May 3, 2021 1 minute ago, Charlie Harley, #14153 said: You were one post ahead of me. Stripped and reassembled mine once. Then settled for flushing with solvent but no taking apart. After I got it apart and realized I was lost, I found a book on gun disassembly and reassembly. They simply said DO NOT TAKE THIS GUN APART! Suggested you put it a pvc tube full of solvent and shake. Pre internet so no you tube help. Link to comment Share on other sites More sharing options...
Warden Callaway Posted May 3, 2021 Share Posted May 3, 2021 I'm working in a Marlin 1891 32. Talk about simple to work on or just clean. There is one thumb screw you loosen and the right side plate comes off. You can lift out the carrier and the bolt. The firing pin just lifts out of the bolt. If you loosen the finger lever spring, you can lift out the lever. Take the buttstock off and take tension off the hammer spring and the hammer will lift out. Link to comment Share on other sites More sharing options...
Michigan Slim Posted May 3, 2021 Share Posted May 3, 2021 Ruger MKII and a Winchester 94. Link to comment Share on other sites More sharing options...
G W Wade Posted May 3, 2021 Share Posted May 3, 2021 Always a laugh when someone brings up the Ruger auto. Tuesday night bullseye league one of the members showed up with what we called the "5 quart holster". An ice cream bucket. I have never needed the "5 quart "holster but my Baikal shotgun scared me bad for a while. When I punched out the pin thru the receiver, cocking pieces fell out both ends of the receiver GW Link to comment Share on other sites More sharing options...
Crooked River Pete, SASS 43485 Posted May 3, 2021 Share Posted May 3, 2021 I know a lot of people have problems with the Ruger MKII, but with you tube They are quite easy. Until some one calls you over to help with one after he has managed to get the trigger and sear out. Link to comment Share on other sites More sharing options...
G W Wade Posted May 3, 2021 Share Posted May 3, 2021 1 minute ago, Crooked River Pete, SASS 43485 said: I know a lot of people have problems with the Ruger MKII, but with you tube They are quite easy. Until some one calls you over to help with one after he has managed to get the trigger and sear out. The problem with the Ruger is the are too good. They rarely need to be cleaned so we do not remember from the last time LOL GW Link to comment Share on other sites More sharing options...
LawMan Mark, SASS #57095L Posted May 3, 2021 Share Posted May 3, 2021 Bought a 1903 Colt for $50 because it was disassembled and the owner couldn't get it back together. I put it back together and sold it for $500. Link to comment Share on other sites More sharing options...
Happy Jack, SASS #20451 Posted May 3, 2021 Share Posted May 3, 2021 One revolver you NEVER try to take apart and reassemble is any of the modern Freedom Arms revolvers. Impossible for anyone who doesn't have the factory "special tools". Link to comment Share on other sites More sharing options...
Sixgun Sheridan Posted May 3, 2021 Share Posted May 3, 2021 51 minutes ago, Crooked River Pete, SASS 43485 said: After I got it apart and realized I was lost, I found a book on gun disassembly and reassembly. They simply said DO NOT TAKE THIS GUN APART! Suggested you put it a pvc tube full of solvent and shake. Pre internet so no you tube help. Did you happen to sell it to a pawn shop in WA state? I always wanted a Nylon 66 and found one, but the first time I shot it the thing jammed constantly. I took it apart and discovered several internal parts literally taped in place! The last owner took it apart and couldn't figure out how to put it back together, and simply sold the hot mess to the shop where I bought it from. Fortunately I found some reference materials online and got it put back together properly. And yes, it's never coming apart again. BTW I can also attest to the Colt Pocket Hammerless. I took one apart once and it took all day to reassemble, cussing in 13 different languages just to get it back together again. Link to comment Share on other sites More sharing options...
Sixgun Seamus Posted May 3, 2021 Share Posted May 3, 2021 I just remember panicking the first time I took the side plates off of a 73 and pieces started falling out. Now it is no big deal to strip down and reassemble. Link to comment Share on other sites More sharing options...
Crooked River Pete, SASS 43485 Posted May 3, 2021 Share Posted May 3, 2021 10 minutes ago, Sixgun Sheridan said: Did you happen to sell it to a pawn shop in WA state? NO, wasn't my gun, which is what caused my panic. I did finally get it together and working right. Link to comment Share on other sites More sharing options...
Yellowhouse Sam # 25171 Posted May 3, 2021 Share Posted May 3, 2021 Anything that requires a good coil spring compressor and you don't have one. The "simple" Stevens 94 shotgun comes to mind. When I was a button couldn't resist dry snapping the hammer and of course the firing pin broke. The only option was to order one from a 56 Stoeger catalog and wait like forever. This 13 year old like to have never got that mainspring back in. Never have I dry fired anything ever again. Link to comment Share on other sites More sharing options...
Big Hand Zack Posted May 3, 2021 Share Posted May 3, 2021 If anyone has had the pleasure of shooting the new Ruger Mk IV's they are just a dream to shoot AND disassemble lol. One push of the rear button and off pops the whole upper barrel assembly. It was about the most perfect upgrade they've ever made. Link to comment Share on other sites More sharing options...
Hardpan Curmudgeon SASS #8967 Posted May 3, 2021 Share Posted May 3, 2021 The first time I did a complete disassembly of my Rossi '92 I was seriously wondering what ol' John Moses had been smoking when he designed it. Not a problem now ~ but I reeeally recommend Nate Kiowa Jones' DVD on the '92: Steve's Gunz Non Sequitur - When disassembling a single action Ruger all experience with Colts and clones won't help ya much. Hint: You can slip the hammer and trigger pivot pins into their respective holes and assemble the internal parts on the outside of the frame to check fit and function. Link to comment Share on other sites More sharing options...
flat iron mike Posted May 3, 2021 Share Posted May 3, 2021 1 hour ago, Sixgun Seamus said: I just remember panicking the first time I took the side plates off of a 73 and pieces started falling out. Now it is no big deal to strip down and reassemble. Ditto, what he said. Link to comment Share on other sites More sharing options...
Rye Miles #13621 Posted May 3, 2021 Share Posted May 3, 2021 46 minutes ago, Big Hand Zack said: If anyone has had the pleasure of shooting the new Ruger Mk IV's they are just a dream to shoot AND disassemble lol. One push of the rear button and off pops the whole upper barrel assembly. It was about the most perfect upgrade they've ever made. I have one and it's a piece of cake to disassemble and assemble. I'm kinda surprised it took them this long to make the change! Link to comment Share on other sites More sharing options...
Willy B.SASS#26902 Posted May 3, 2021 Share Posted May 3, 2021 I've had two disassembled guns given to me, one was a Remington model 8 which has a million small pieces, The other was the previously mentioned Colt 1903 which was by far the worst. I don't remember the brand but I put a 22 auto together for a guy I worked with the only way to get the recoil springs back in was to compress them in aquarium tubing. Link to comment Share on other sites More sharing options...
Waxahachie Kid #17017 L Posted May 3, 2021 Share Posted May 3, 2021 Ruger Mark I .22 semi-automatic. Never again, unless I have the instructions right there before me, and a bottle of Anejo tequila, salt, and lime, to dull the pain of it. Link to comment Share on other sites More sharing options...
Chili Ron Posted May 3, 2021 Share Posted May 3, 2021 Howdy, With the wonderful cleaners on the market why take apart anything not in dire need of repairs? Best' CR Link to comment Share on other sites More sharing options...
Forty Rod SASS 3935 Posted May 3, 2021 Share Posted May 3, 2021 5 hours ago, DeaconKC said: The 1903 Colt? EGADS! You are correct. The only gun that ever beat me is a Remington M-51 .32 acp. It's one of the best feeling, most ergonomic pieces I ever owned, and hits where I look without using the miniscule sights, but it has more parts than a Edsel, all small as a pin head, and NO SCREWS ANYWHERE. It's a Pederson design and very well made, but it's a puzzler's nightmare. I even found a tutorial on the internet but it still stumped me. Link to comment Share on other sites More sharing options...
Blackwater 53393 Posted May 3, 2021 Share Posted May 3, 2021 I took down an Iver Johnson hammerless double once to replace the mainsprings! I eventually made a tool out of a giant “C” clamp in order to reinstall the springs. NEVER AGAIN!! Link to comment Share on other sites More sharing options...
Henry T Harrison Posted May 3, 2021 Share Posted May 3, 2021 I’ll add my vote for the 1903. The only gun that ever defeated me Link to comment Share on other sites More sharing options...
Kid Rich Posted May 3, 2021 Share Posted May 3, 2021 An original 86 Winchester. Half a day to take it apart (completely) and a full day to reassemble. No, I did not have a manual. The 92's and 94's I have disassembled were a piece of cake in comparison. kR Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.