Marshall Matt Dillon Posted March 27, 2021 Posted March 27, 2021 Marlin 1894 in 45 colt. Which trigger do people like best?
Warden Callaway Posted March 27, 2021 Posted March 27, 2021 I have the Phantom trigger in most of our Marlins.
McCandless Posted March 27, 2021 Posted March 27, 2021 9 hours ago, Marshall Matt Dillon said: Marlin 1894 in 45 colt. Which trigger do people like best? After working with both of them, I prefer the flatter profile of the Ranger Point trigger. They both function well, but the end of the Happy Trigger was hitting me right in the pad of my finger.
Marshall Matt Dillon Posted March 28, 2021 Author Posted March 28, 2021 5 hours ago, McCandless said: After working with both of them, I prefer the flatter profile of the Ranger Point trigger. They both function well, but the end of the Happy Trigger was hitting me right in the pad of my finger. Good info there.thanks
Nate Kiowa Jones #6765 Posted March 28, 2021 Posted March 28, 2021 I prefer the WWG happy trig. They have been around for sometime now. Over the years, I have installed several in customer guns without any issues or complaints.
Rough 'N Ready Rob Posted March 29, 2021 Posted March 29, 2021 I would not buy a Trigger Happy had one in my 45-70 Marlin, it would go off out of battery. Contacted the seller, that makes them. They were no help. I will never buy from them again. Put the stock trigger back in, gun works fine, safe again.
Warden Callaway Posted March 29, 2021 Posted March 29, 2021 Ok, here is my take on the situation. The Marlin 1894 was reintroduced in 1969. So considering 52 years of production there is some design and parts variations. And, I expect ever Marlin was hand fitted at the factory. It's just good luck any trigger or interlock replacement worked correctly. It could end up failing. Could be the trigger wouldn't release at all. I went through our stash of Marlins with the Phantom trigger and found one that would let the hammer drop with lever open. Here is the relationship of the trigger and interlock. Note the gap. Here I've taken the trigger plate out and put the hammer back in to better test the function. I drove the pin out that holds the trigger reset and safety do-hicky. I didn't have a new replacement so I cold "forged" the corner edgen move metal forward a bit to fill the gap. Helps to use a "slave pin" to align the holes. You have to "mash down" on the spring to get the pin to pass. I took several beatings and testing before I moved enough metal to make it work. The metal was harder than I expected. A replacement part would be great but parts are hard to get now. If I'm faced with doing this again, I'd just get out the torch and heat that edge to dull red and hit it. Works now.
The Rainmaker, SASS #11631 Posted March 30, 2021 Posted March 30, 2021 Found a source of original Marlin one-piece triggers. Some I've had to clean up a bit and re-blue but have installed in both of my Marlins and they work great! No two-piece trigger flop! And they look great too; never cared for the gaudy gold ones. I have a couple spares for just the right occasion.
The Original Lumpy Gritz Posted March 30, 2021 Posted March 30, 2021 23 minutes ago, The Rainmaker, SASS #11631 said: Found a source of original Marlin one-piece triggers. Some I've had to clean up a bit and re-blue but have installed in both of my Marlins and they work great! No two-piece trigger flop! And they look great too; never cared for the gaudy gold ones. I have a couple spares for just the right occasion. Could you share the name of this source? OLG
Warden Callaway Posted March 30, 2021 Posted March 30, 2021 1 hour ago, The Rainmaker, SASS #11631 said: Found a source of original Marlin one-piece triggers. Some I've had to clean up a bit and re-blue but have installed in both of my Marlins and they work great! No two-piece trigger flop! And they look great too; never cared for the gaudy gold ones. I have a couple spares for just the right occasion. I have a bunch of early 1894s (1894-WWI) and none of them have the trigger block interlock feature. If the two-piece firing pin is working, it's a redundant feature. Ironically, the 1894 was an update of the 1889. The 1889 had a trigger block and two piece trigger.
The Rainmaker, SASS #11631 Posted March 30, 2021 Posted March 30, 2021 1 hour ago, The Original Lumpy Gritz said: Could you share the name of this source? OLG I can... but it'll cost ya. Lol Seriously, it's Numrich, but they are out on all 1894 listings for one-piece triggers. I may have bought the last they had. I do know the same trigger was installed in different models, but after a little looking, they are out.
Warden Callaway Posted March 30, 2021 Posted March 30, 2021 I dug out an old 1894 solid trigger (with broken sear) and a Phantom trigger. I don't see how the old Marlin one-piece trigger would interface with a trigger block as its not got a "butt" to butt up to the trigger block.
The Rainmaker, SASS #11631 Posted March 31, 2021 Posted March 31, 2021 Can't tell you without pulling it out and having a look, but it works. One for one (two) swap. They work great and I haven't changed anything else.
Recommended Posts
Archived
This topic is now archived and is closed to further replies.