Go West Posted January 15, 2021 Share Posted January 15, 2021 I know the trend is towards wet tumbling, but I'm still doing it dry and am slow to change. If you're still tumbling with dry media, what additives do you like? I'm wondering if some of the products used in wet tumbling would also work with corn cob or lizard litter. Link to comment Share on other sites More sharing options...
twelve mile REB Posted January 15, 2021 Share Posted January 15, 2021 A little liquid Turtle wax and a drier sheet, brass comes out beautiful. The drier sheet keeps the dust down to almost nothing and with a hundred pounds of corn cob not changing soon. Link to comment Share on other sites More sharing options...
High Spade Mikey Wilson Posted January 15, 2021 Share Posted January 15, 2021 The last time I ordered corn media, I think it was from Cabela's, they sent along a 3 oz. bottle of brass polish with it. Works great. Link to comment Share on other sites More sharing options...
Marshal Hangtree Posted January 15, 2021 Share Posted January 15, 2021 So here's a question I've always wanted to ask on this subject. Do you just add the brass polish/detergent/lemi-shine straight to the dry media? Seems like it would get stuck in one place to me. How does the liquid get dispersed in the dry media? Thanks. Link to comment Share on other sites More sharing options...
Eyesa Horg Posted January 15, 2021 Share Posted January 15, 2021 19 minutes ago, Marshal Hangtree said: So here's a question I've always wanted to ask on this subject. Do you just add the brass polish/detergent/lemi-shine straight to the dry media? Seems like it would get stuck in one place to me. How does the liquid get dispersed in the dry media? Thanks. When I add the Turtle Polish I just pour a little bit in and run the tumbler for 10 minutes or so and then use a stick to break up the small clumps. Doesn't take too long. I also soak my brass first in a mix of 50/50 water & Simple green. Shake once in a while for about half an hour. Dry in an old food dehydrator and then into the tumbler for an hour. They look like new. Inside is still a little discolored but not bad. Be sure to get them dry to avoid any corrosion in the primer pockets as i don't usually deprime before cleaning. Using the drier sheets seems to help with dust and the media last me quite some time, using corn cob I get a year or so out of a batch before it gets too gray. Link to comment Share on other sites More sharing options...
The Rainmaker, SASS #11631 Posted January 15, 2021 Share Posted January 15, 2021 If you add the solution slowly without the brass and let it run for a bit, it will mix up ok Link to comment Share on other sites More sharing options...
Garrison Joe, SASS #60708 Posted January 15, 2021 Share Posted January 15, 2021 I no longer add any car wax to my lizard litter, as I would (rarely) get clumps of wax and media in my cases, even when I usually remembered to let the wax run for a few minutes before adding cases. So, now it's just the lizard litter and a dryer sheet (used) and a cap of paint thinner (maybe a tablespoon). Run vibratory bowl for 30 minutes. Brass gets as clean as I need, and even a little shiny. good luck, and good enough for me, and no waiting for wax to spread out, GJ Link to comment Share on other sites More sharing options...
Cayuse Jack, SASS #19407 Posted January 15, 2021 Share Posted January 15, 2021 I use lizard litter crushed walnut that I buy from the pet store. Pre treat the media with scratch and swirl remover used on automobiles (a couple ounces). Just pour it on and run the tumbler a couple minutes to let it mix together. Then each time before I run a batch I add about a half ounce of the swirl remover to the media and tumble to mix. My brass is beautiful after about an hour. Link to comment Share on other sites More sharing options...
Cypress Sam, SASS #10915 Posted January 15, 2021 Share Posted January 15, 2021 I use walnut shell media but this would work with corncob media too. Squirt a shot of auto polish (not wax) into the media bowl and add about a tablespoon of mineral spirits or paint thinner. Then run your vibratory tumbler for a few minutes to thoroughly mix. I usually let the tumbler run overnight, but about an hour probably would work. Any brand of auto polish works as long as it doesn’t have wax in it. The mineral spirits not only cuts the grease on the brass but, more importantly keeps the dust down. My brass comes out looking like new. Link to comment Share on other sites More sharing options...
Eyesa Horg Posted January 15, 2021 Share Posted January 15, 2021 Wouldn't the mineral spirits tend to remove the polish? I use spirits in the media I clean loaded cartridges with to get the lube off. Works good but does seem to remove the polish. Link to comment Share on other sites More sharing options...
Hashknife Cowboy Posted January 15, 2021 Share Posted January 15, 2021 I do a 50/50 mix of these.....works great. Link to comment Share on other sites More sharing options...
Perro Del Diablo Posted January 15, 2021 Share Posted January 15, 2021 I use Dillon rapid polish most times but I have also used Nufinish car polish with good results. Brasso is another option. Link to comment Share on other sites More sharing options...
J-BAR #18287 Posted January 15, 2021 Share Posted January 15, 2021 Mixed black powder and smokeless .38 Specials, tumbled in a Dillon CV750 case cleaner (the smaller one), using ground corn cob media and Dillon Rapid Polish 290. These are all brass cases, no nickel cases in there. Some catch the light more directly. No, I don't keep track of how many times a case has been loaded. No I don't keep black powder and smokeless cases separated. Samee, samee, alla samee. After dumping the dirty brass into the media, I stir the cases down into the media to bury them, then pour a thin line of polish in a circle on top of the media, maybe a tablespoon at the most. Tumble 4 to 6 hours. These have been reloaded several times. I stood a few up so you can see the inside of the case; new unfired brass is shiny inside too. About once a year I clean the film of polish from inside the tumbler bowl. Mineral spirits on a paper towel cleans it off easily. Link to comment Share on other sites More sharing options...
Marshal Chance Morgun Posted January 15, 2021 Share Posted January 15, 2021 In case you didn't catch it, make should that is a used dryer sheet Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.