Warden Callaway Posted November 26, 2020 Share Posted November 26, 2020 Waiting for the turkey to get on the table and family to show up, I've been keeping busy with projects. I picked up some 1/4" drive magnetic driver bits at a flea market 10 for $5.00. I epoxied the shanks into blocks. In this case walnut. I turned the upper on on my little metal lathe and put a coat of Tru-Oil on it earlier this morning. The lower is "before". I collected the memory card from a trail cam I placed to cover the carcass of a deer my son found dead. It took two videos to cover the traffic. Just got noticed son is on his way. Link to comment Share on other sites More sharing options...
Pat Riot Posted November 26, 2020 Share Posted November 26, 2020 Neat videos. Lots of animal activity. Link to comment Share on other sites More sharing options...
DocWard Posted November 26, 2020 Share Posted November 26, 2020 My Thanksgiving morning projects were to go get propane for the grill, then to remove the bad heating element from the oven so we can at least use the stovetop. Next challenge will be to cook a turkey breast on the grill. Link to comment Share on other sites More sharing options...
Badlands Bob #61228 Posted November 26, 2020 Share Posted November 26, 2020 I drained the camper of water from our recent 2 week trip. Then filled all the traps with RV antifreeze. It's going down to 25 degrees on Monday. I've still got 4 guns to clean but I think I'll put that off until after the match on Saturday. Maybe its time for a nap. Link to comment Share on other sites More sharing options...
DeaconKC Posted November 26, 2020 Share Posted November 26, 2020 Still packing after the Missus made a fine Thanksgiving meal for us. Link to comment Share on other sites More sharing options...
LawMan Mark, SASS #57095L Posted November 26, 2020 Share Posted November 26, 2020 I put a slow cooker pot of pinto beans on this morning. Took care of some internet stuff, then the wife and I took a ride in the Miata for a couple of hours. Stopped at a local city park and had a very light lunch while watching the fountain. Got home and got the turkey breast into the oven, should take about 2 1/2 to 3 hours to cook. Link to comment Share on other sites More sharing options...
Dirty Dog Doug Posted November 26, 2020 Share Posted November 26, 2020 we went to the Range Since it was just fun and practice I shot better than at the real match last weekend lubes and adjust all our moving targets normally I get truck envy soo many new trucks in the parking lot while my 2002 F150 still runs great . we see this fancy flying gun cart Link to comment Share on other sites More sharing options...
Abilene Slim SASS 81783 Posted November 26, 2020 Share Posted November 26, 2020 Been having trouble with an older S&W K-10 where the bolt would rise before the cylinder turned, thus locking it up. I’ve never owned one these much less take it apart. Today I dove in and took it completely apart. No parts showed any wear etc. so I just put it back together. Now it works perfectly. No idea what I did, but I’m not complaining. At least now I know how to disassemble and reassemble one. A good day. Link to comment Share on other sites More sharing options...
Abilene Slim SASS 81783 Posted November 26, 2020 Share Posted November 26, 2020 9 minutes ago, Dirty Dog Doug said: we went to the Range Since it was just fun and practice I shot better than at the real match last weekend lubes and adjust all our moving targets normally I get truck envy soo many new trucks in the parking lot while my 2002 F150 still runs great . we see this fancy flying gun cart The second and third targets look devious! Link to comment Share on other sites More sharing options...
Texas Joker Posted November 26, 2020 Share Posted November 26, 2020 Did a .50 cent action job on a new Rossi 45. Took it all apart smoothed it out pre loaded the trigger spring and swapped the ejector spring after I put the turkey in. Functioned checks great. Made a bunch of difference on the rifle Link to comment Share on other sites More sharing options...
Dirty Dog Doug Posted November 26, 2020 Share Posted November 26, 2020 46 minutes ago, Abilene Slim SASS 81783 said: The second and third targets look devious! the last target of first plate rack gets me 3" across with pistol the third one we can shoot the swinger or shoot threw the hole and not hit any steel Our fast shooters hit it on both outsides and the center Link to comment Share on other sites More sharing options...
Warden Callaway Posted November 27, 2020 Author Share Posted November 27, 2020 Can someone with knowledge of raptors identify these in this video clip? I'm guessing juvenile bald eagle. Link to comment Share on other sites More sharing options...
Blackwater 53393 Posted November 27, 2020 Share Posted November 27, 2020 Finished prepping the turkey for roasting. Updated my Craigslist account. Made breakfast for myself, (Schoolmarm had already eaten) With the exception of carving the turkey, I did little or nothing the rest of the day!! Link to comment Share on other sites More sharing options...
Bladesmith Posted November 27, 2020 Share Posted November 27, 2020 Started a new batch of knives. Here are some I just finished Link to comment Share on other sites More sharing options...
DeaconKC Posted November 28, 2020 Share Posted November 28, 2020 I love those in the second pic! Link to comment Share on other sites More sharing options...
Charlie MacNeil, SASS #48580 Posted November 28, 2020 Share Posted November 28, 2020 On 11/26/2020 at 9:34 AM, Warden Callaway said: I collected the memory card from a trail cam I placed to cover the carcass of a deer my son found dead. It took two videos to cover the traffic. Them's kinda funny-lookin' deer. Their ears is too short and they got some kinda furry thing hangin' on their hineys... Link to comment Share on other sites More sharing options...
Silver Creek Jack Posted November 28, 2020 Share Posted November 28, 2020 Beautiful knives, really like the ones in the third pic from the top! Link to comment Share on other sites More sharing options...
Bladesmith Posted November 28, 2020 Share Posted November 28, 2020 Thank you for the complements. This was the first time I made the style in the second picture. The pattern in the third picture is one of my favorites. Link to comment Share on other sites More sharing options...
watab kid Posted December 1, 2020 Share Posted December 1, 2020 nice knife work , Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.