Cactus Jack Calder Posted September 15, 2020 Share Posted September 15, 2020 Right now I’m working on my 45 ACP brass. I sized and deprimed the cases, ran them in an ultrasonic cleaner and rinsed them really well with warm water. I used OLG’s suggestion and rolled them back and forth hanging in an old towel. The outsides are dry, however, I can see a little water in the bottom of the shells. The question of the day is; What is the best (most efficient) way of drying the inside of the cases? Have at it and thank you! Please note, I am alone here. Not without family, without a mentor to teach me his/her methods of reloading. So you’s guys are my de facto mentors. Any help is greatly appreciated. CJ Link to comment Share on other sites More sharing options...
Bingo Montana Posted September 15, 2020 Share Posted September 15, 2020 An inexpensive food dehydrator makes a great brass drier. Link to comment Share on other sites More sharing options...
H. K. Uriah, SASS #74619 Posted September 15, 2020 Share Posted September 15, 2020 I've never used water to clean my .45 ACP brass. Never seen a need to do so. I just tumble them in the corn cob and then reload them. That being said, I have on occasion had to use water to rinse our some 12 gauge all brass shells. After cleaning them, I shook out the excess water and left them sitting out overnight on the counter to dry. Link to comment Share on other sites More sharing options...
Judge Gardner Posted September 15, 2020 Share Posted September 15, 2020 Lyman case dryer Link to comment Share on other sites More sharing options...
Sedalia Dave Posted September 15, 2020 Share Posted September 15, 2020 I spread all my brass out on cookie sheet(s) and sit them in the sun for an hour or so. I bought the cookie sheets specifically for the reloading room and use them for a multitude of tasks. Link to comment Share on other sites More sharing options...
Eyesa Horg Posted September 15, 2020 Share Posted September 15, 2020 I pre-clean my brass in a mix of H2O & Simple Green and as stated above then dry them in an old food dehydrator for 1 1/2 hours. They come out dry and no water spots. Then into the vibratory tumbler with corn cob/polish for another 1 1/2 hours. They always look like new. Link to comment Share on other sites More sharing options...
Loophole LaRue, SASS #51438 Posted September 15, 2020 Share Posted September 15, 2020 Jerry Miculek wet tumbles in a cement mixer and dries in an old oven.... If it works, do it! Link to comment Share on other sites More sharing options...
Cactus Jack Calder Posted September 15, 2020 Author Share Posted September 15, 2020 Several ideas I can work with. 1. Bingo, My son up the road had a dehydrator. I think he stopped using it. I’ll have to ask him about that. 2. SD thanks, I just remembered I have a cookie sheet not suitable for food that I can use. 3. Loophole, Mr. Miculek certainly has his method worked out efficiently. I can use one of the ovens. We have two, one over, one under. The under one is used for storage, so I can probably use it. There shouldn’t be much odor involved. Thank you all, Look for future what to do’s as I progress down the road. CJ Link to comment Share on other sites More sharing options...
Springfield Slim SASS #24733 Posted September 15, 2020 Share Posted September 15, 2020 I just put them on an old towel and put in the sun to dry. Link to comment Share on other sites More sharing options...
Sarge Posted September 15, 2020 Share Posted September 15, 2020 If I'm not in a hurry, I lay them out on a plastic sheet for a few days in the basement. If I'm in a hurry, I use a small toaster oven I picked up for a couple of bucks at a Salvation Army Store. About a half an hour at 200 degrees usually does it. It doesn't come out pretty and shiny, but it is clean and serviceable. Link to comment Share on other sites More sharing options...
Turkey Flats Jack Posted September 15, 2020 Share Posted September 15, 2020 there's a couple ways that i've tried and work well. I have an old chicken egg incubator and used that. Works the same as the more expensive case dryers or food dehydrators. I've also spread them out on some hardwire cloth nailed to a 1x2 frame and put a fan blowing on them. both ways will get them dry overnight. I'm sure there's lots of other ways. I will say do not put them in a pillow case and toss them in the dryer. besides the fact that it's pretty loud the mrs wasnt real thrilled with it. Jack Link to comment Share on other sites More sharing options...
Matthew Duncan Posted September 15, 2020 Share Posted September 15, 2020 2 hours ago, Cactus Jack Calder said: ...The outsides are dry, however, I can see a little water in the bottom of the shells. The question of the day is; What is the best (most efficient) way of drying the inside of the cases? ... CJ I place my wet tumble brass on a towel and let air dry. Takes a day or three depending on the humidity inside my house. Reckon a cowpoke could speed that up by setting them in the sun. Link to comment Share on other sites More sharing options...
Marshal Chance Morgun Posted September 15, 2020 Share Posted September 15, 2020 Wife's hair dryer? Link to comment Share on other sites More sharing options...
Lucky Lead Pepper Posted September 15, 2020 Share Posted September 15, 2020 Sometimes I put them on a cookie sheet and put them in the oven around 150-170. Sometimes I lay them on a towel on my bench with the case mouth facing the edge of the bench. Then I put an oscillating fan in front of them and leave them for a few hours. So far so good. Link to comment Share on other sites More sharing options...
Abilene Slim SASS 81783 Posted September 16, 2020 Share Posted September 16, 2020 1 hour ago, Springfield Slim SASS #24733 said: I just put them on an old towel and put in the sun to dry. Yup! I’m a big fan of solar power. Link to comment Share on other sites More sharing options...
Chancy Shot, SASS #67163 Posted September 16, 2020 Share Posted September 16, 2020 1 hour ago, Marshal Chance Morgun said: Wife's hair dyer? Did Penny see this? You are living dangerously. Chancy Link to comment Share on other sites More sharing options...
Cactus Jack Calder Posted September 16, 2020 Author Share Posted September 16, 2020 Well I found my old cookie sheet and put them in the oven at 170 F. one layer all laying flat so that both ends are off the sheet. It seems to be working ok. I will use the sun next time with my 38 spl brass.. I’m sure I’ll be back for more help soon. I am looking at YouTube for reloading videos also. Thanks again. CJ Link to comment Share on other sites More sharing options...
Church Key, SASS # 33713 Posted September 16, 2020 Share Posted September 16, 2020 When I was shooting BP, I would wash them and set them outside on a cookie sheet. If it was near freezing on a cookie sheet in the basement for a day or so. Link to comment Share on other sites More sharing options...
J-BAR #18287 Posted September 16, 2020 Share Posted September 16, 2020 57 minutes ago, Chancy Shot, SASS #67163 said: Did Penny see this? You are living dangerously. Chancy Tell your wife to get a new hair dryer and appropriate the old one. Or spend $15 on a cheap heat gun from Harbor Freight. Link to comment Share on other sites More sharing options...
Buffalo Bill Mathewson, 37826 Posted September 16, 2020 Share Posted September 16, 2020 To dry brass I have used the oven set at 250, bake timer set for one hour. Had a live round in a batch of brass I forgot to pull when done. The wife went to preheat the oven to 450 for a pizza. The live round cooked off about the time the oven was up to temp. It was a bit exciting for just a little bit. The case split and both the bullet and split case stayed in the tinfoil pan I had the brass in. I think it was good that the round was a smokeless round rather than BP or Sub. Link to comment Share on other sites More sharing options...
The Original Lumpy Gritz Posted September 16, 2020 Share Posted September 16, 2020 I use a fan. OLG Link to comment Share on other sites More sharing options...
Choctaw Jack Posted September 16, 2020 Share Posted September 16, 2020 I use the same toaster oven that I use to bake my cast bullets after powder coat. Link to comment Share on other sites More sharing options...
El Hombre Posted September 16, 2020 Share Posted September 16, 2020 Put them outside on a table on top of a towel for a couple of days depending on how warm it is Link to comment Share on other sites More sharing options...
Tequila Shooter Posted September 16, 2020 Share Posted September 16, 2020 Living as far south as I do in the summer I can lay them in the sun for an afternoon and they’re dry. Did you de-prime before tumbling? It makes a difference for air flow. In the winter I use an air compressor to blow out any water then lay them out on the shop floor (in front of the dehumidifier). Always check to make sure the primer pocket is dry before reloading. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.