Imis Twohofon,SASS # 46646 Posted July 11, 2020 Share Posted July 11, 2020 I am about to begin my annual shotgun shell reloading after reading other threads on reloading and Blood Lead Levels( BLL). I did not want to hijack those threads to ask specifically about any ideas to cut down on GunShot Residue on SG hulls. Have you tried washing and drying them, any chemical applications etc? We seem to have covered metallic cartridges aspects pretty thoroughly but not SG. Imis (My BLL was 13 in Jan, 2019. Untested since, I am taking further measures since that time) Link to comment Share on other sites More sharing options...
John Boy Posted July 11, 2020 Share Posted July 11, 2020 Quote We seem to have covered metallic cartridges aspects pretty thoroughly but not SG. Imis - 25 shotgun reloads x the number of matches shot per year ... count them up Personally, I wouldn't loose sleep worrying that you blood level would go through the roof because primarily you are 'pouring' shot into the case from the press not handle-ling center fire bullets into the cases using the press I have 9 cases of black & smokeless shotgun reloads for cowboy and trap ... my levels are still in the 12 range and this includes casting and reloading many 100 round boxes of centerfires Link to comment Share on other sites More sharing options...
Kid Rich Posted July 11, 2020 Share Posted July 11, 2020 If you are worried about the residue on sg shells wash them in a 5 gallon bucket with some delead laundry soap. don't let them stay wet for very long as the primers may corrode. kR Link to comment Share on other sites More sharing options...
J-BAR #18287 Posted July 11, 2020 Share Posted July 11, 2020 Moisten a paper towel with case lube or Armor All and wipe the hulls off before running them through the press. Wash your hands and reload. I do them in batches of 50. Keeps your dies clean too. Link to comment Share on other sites More sharing options...
Rye Miles #13621 Posted July 12, 2020 Share Posted July 12, 2020 I wouldn't worry about shot, it's actually handling lead bullets that's the culprit. I was told to wash your hands real good after reloading. Link to comment Share on other sites More sharing options...
Dusty Devil Dale Posted July 12, 2020 Share Posted July 12, 2020 My MEC loader has a persistent problem of retaining a couple pellets from each drop, then dumping them onto the stage or table when I next pull the handle down. Stray shot lying around the bench is a bad source of lead assimilation, and if it gets on the hard floor, it is also a serious ball bearing slip-fall hazard. I spend the effort as needed to contain stray shot and not let it get away into my blood or elsewhere. I also have concern over the dust that comes out all over the bench and in the air when shot is poured from the bags into the loader magazine flasks. A lot of it is graphite dust, but I've captured and heated it in an annealing oven, and an appreciable part of it is also metallic lead. So I wear long sleeves, gloves, and a dust mask when pouring shot. Then I wash my hands soon afterwards. But I don't worry too much about the lead that actually makes it into the shell cases. It isn't going anywhere except downrange. Link to comment Share on other sites More sharing options...
Garrison Joe, SASS #60708 Posted July 12, 2020 Share Posted July 12, 2020 Wash hands thoroughly after loading your shotshells. Wash hands thoroughly after shooting them. The inhalation exposure from shooting shotshells occurs during the shooting itself - for that, a fine particulate mask would be needed. I'd say it's hardly something to get too worked up over. GJ Link to comment Share on other sites More sharing options...
Roscoe Regulator Posted July 12, 2020 Share Posted July 12, 2020 You could wear nitrile gloves or at least try that. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.