The Verdigris Kid Posted June 3, 2020 Share Posted June 3, 2020 I have a chance to pick up a nice looking Winchester 97, however it has a full length barrel with what looks to be an Poly-Choke on it. Would this shotgun be legal to use in SASS? Link to comment Share on other sites More sharing options...
Cholla Posted June 3, 2020 Share Posted June 3, 2020 Many cut the barrel down to 20" so I don't see a problem. Link to comment Share on other sites More sharing options...
Garrison Joe, SASS #60708 Posted June 3, 2020 Share Posted June 3, 2020 Not legal in Wild Bunch part of SASS with the polychoke on it. That choke might also be in violation of SASS Cowboy rules by being a visible external modification, as I don't believe Winchester put on PolyChokes at the factory. As Cholla mentioned, have barrel trimmed to a shorter length - it will look better and for our matches, shoot better too. Shouldn't cost more than $100 to have it done. Good luck, GJ Link to comment Share on other sites More sharing options...
The Verdigris Kid Posted June 3, 2020 Author Share Posted June 3, 2020 Thanks guys, that is kind of what I was thinking that it wouldn't be legal. But it is so nice looking I hate to think of chopping the barrel. Link to comment Share on other sites More sharing options...
Garrison Joe, SASS #60708 Posted June 4, 2020 Share Posted June 4, 2020 Well, if you consider that any gun used for Cowboy shooting will look pretty worn after a year, I'm not sure why you are concerned about using a pretty gun that will be worn in a year. If you can get it for a good price, and it works, that is all I want. A poly-choked shotgun is not a collectable to almost anyone. A Cutts Compensator is a collector's item to a few shooters, though (mainly Skeet shooters). Good luck, GJ Link to comment Share on other sites More sharing options...
Colorado Coffinmaker Posted June 4, 2020 Share Posted June 4, 2020 PLUS ONE too Garrison Joe. Poly Choke is NOT legal for SASS nor WB. If you elect to cut the barrel yourself .... DO NOT USE A PIPE CUTTER!! Link to comment Share on other sites More sharing options...
Noz Posted June 4, 2020 Share Posted June 4, 2020 One reason for not using a pipe cutter, if the barrel sides are not parallel, the cutter will migrate toward the smaller end leaving a nasty mess that will have to be done in some other fashion. Yes, I have a 20 ga barrel that looks like some one tried to thread about 3" of the barrel. Link to comment Share on other sites More sharing options...
Newt Ritter Posted June 4, 2020 Share Posted June 4, 2020 You can use a pipe cutter - wrap tape (masking tape, electrical tape, duck tape) around the forward part of the barrel (the narrower part) above where you want to make the cut. Do that until you have built up that narrow part to where it is the same dimension as the broader part and, with part of your pipe cutter resting on that taped section, you can cut a relatively straight line. At least as straight as I was ever able to manage a hacksaw cut. Then with a little filing, a little round filing around the barrel to make it look nicer, and a little touch up bluing it should look real good. Oh, good luck with the bluing on the steel of a '97. Link to comment Share on other sites More sharing options...
Garrison Joe, SASS #60708 Posted June 4, 2020 Share Posted June 4, 2020 Careful with a pipe cutter - it bends the barrel wall in at the cut to produce a false (and inaccurate) mini choke. Simple to find a gunsmith who will cut off in a lathe and deburr the muzzle and even install a new bead. Good luck, GJ Link to comment Share on other sites More sharing options...
Marauder SASS #13056 Posted June 5, 2020 Share Posted June 5, 2020 3 hours ago, Garrison Joe, SASS #60708 said: Careful with a pipe cutter - it bends the barrel wall in at the cut to produce a false (and inaccurate) mini choke. Simple to find a gunsmith who will cut off in a lathe and deburr the muzzle and even install a new bead. Good luck, GJ Surre! Do it the easy way! Link to comment Share on other sites More sharing options...
Cholla Posted June 5, 2020 Share Posted June 5, 2020 6 hours ago, Garrison Joe, SASS #60708 said: Careful with a pipe cutter - it bends the barrel wall in at the cut to produce a false (and inaccurate) mini choke. Simple to find a gunsmith who will cut off in a lathe and deburr the muzzle and even install a new bead. Good luck, GJ This times ten. I have cut enough hard pipe and tubing to verify it. If the cutting wheel is dull, it can close the ID to almost half. Any use of a pipe cutter requires reaming the inside of the pipe so it doesn't sound like a great idea for a shotgun. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.