Jump to content
SASS Wire Forum

"Swiss Army" Hardware Store


Subdeacon Joe

Recommended Posts

A “Swiss Army” knife made in Solingen, Germany...:rolleyes:

 

I was trying to determine it’s size. It almost looks like the scale panels open up to expose a bunch of little tiny knives and scissors. 

 

 

Link to comment
Share on other sites

21 hours ago, Pat Riot, SASS #13748 said:

A “Swiss Army” knife made in Solingen, Germany...:rolleyes:

 

I was trying to determine it’s size. It almost looks like the scale panels open up to expose a bunch of little tiny knives and scissors. 

 

 

Those scales are hinged and there are release levers at the middle of the handle!  I would not have spotted them if you had not commented.

 

Duffield

Link to comment
Share on other sites

On 2/1/2020 at 9:21 AM, Pat Riot, SASS #13748 said:

I was trying to determine it’s size

You just need some scale, right?

 

A 5 shot 22 revolver has got to be at least three quarters of an inch through the cylinder.

 

The gun is visible in the first picture, so just use the cylinder diameter of 3/4 of an inch and measure it out.

Link to comment
Share on other sites

51 minutes ago, Alpo said:

You just need some scale, right?

 

A 5 shot 22 revolver has got to be at least three quarters of an inch through the cylinder.

 

The gun is visible in the first picture, so just use the cylinder diameter of 3/4 of an inch and measure it out.

That’s a big knife!

 

 

 

Anyone notice there are no flat or Phillips screwdriver blades but there are 10 different scissors of various shapes and sizes. 

Link to comment
Share on other sites

59 minutes ago, Pat Riot, SASS #13748 said:

Anyone notice there are no flat or Phillips screwdriver blades but there are 10 different scissors of various shapes and sizes. 

Top picture right side. Isn't that a straight slot screwdriver?

IMG_20200202_191122.jpg

Link to comment
Share on other sites

Howdy,

Looks like a Philips top side center and bottom side to the left.

A lot of ends of other tools serve as flat screwdrivers.

Plus a screwdriver goes into the corkscrew if ordered.

Any tool I cant comfortably hold in my hand is of doubtful value.

 

Best

CR

 

Link to comment
Share on other sites

1 hour ago, Alpo said:

Top picture right side. Isn't that a straight slot screwdriver?

IMG_20200202_191122.jpg

Yep, looks like you’re right. That definitely looks like a screwdriver. :)

Link to comment
Share on other sites

13 minutes ago, Chili Ron said:

Howdy,

Looks like a Philips top side center and bottom side to the left.

A lot of ends of other tools serve as flat screwdrivers.

Plus a screwdriver goes into the corkscrew if ordered.

Any tool I cant comfortably hold in my hand is of doubtful value.

 

Best

CR

 

I am not seeing them. 
 

Is that a tuning fork? Top photo, right side, almost halfway up from the bottom. 

Link to comment
Share on other sites

On 2/1/2020 at 8:21 AM, Pat Riot, SASS #13748 said:

A “Swiss Army” knife made in Solingen, Germany...:rolleyes:

 

I was trying to determine it’s size. It almost looks like the scale panels open up to expose a bunch of little tiny knives and scissors. 

 

 

 

15 hours ago, Duffield, SASS #23454 said:

Those scales are hinged and there are release levers at the middle of the handle!  I would not have spotted them if you had not commented.

 

Duffield

MEASUREMENTS
average spatial: 3 1/2 in x 3 1/2 in x 9 1/4 in; 8.89 cm x 8.89 cm x 23.495 cm

 

2X7oWpW

X8zEdTX

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.