Croc Holiday Posted August 10, 2019 Share Posted August 10, 2019 I’ve got a small garage and too much crap. I don’t have space for a dedicated loading bench. I do have a work bench I use for all sorts of projects. I’m considering mounting the presses to something like 3/4” ply or particle board so I can clamp it to the bench when I need it and shelf it when I don’t. Another option I thought of was getting a cheap little kitchen island cart and mounting it to that so I can roll it out to use it and roll it out of the way to store it. Before I commit to one, I thought I’d see what other folks do. Is there a better option I haven’t considered? Link to comment Share on other sites More sharing options...
Tyrel Cody Posted August 10, 2019 Share Posted August 10, 2019 My Lee Turret press is mounted on a piece of 2×6 that's about a foot long and I clamp it to a workbenches. I did that so I could take a press to the range easily. I have quick change mounts for my Hornady Lock N Loads and my MEC. https://inlinefabrication.com/collections/quick-change-press-mounting-system Link to comment Share on other sites More sharing options...
Muley Gil SASS # 57795 Posted August 10, 2019 Share Posted August 10, 2019 The best option IS the press on a board clamped to the work bench. Back in college, I loaded ammo in my dorm room and cast bullets in the bathroom at the end of the hall. My press (first a RCBS Jr and then a RCBS Rockchucker) was bolted to a tiny bench. The bench had an about 18"x8" top and a 24"x8" bottom board with two (2) 18"x8" risers. I would sit on the floor to reload. All of my gear-dies, bullets, powders, bullets, etc. was stored in a cardboard box that I kept in my closet. Link to comment Share on other sites More sharing options...
Smokey Dave Posted August 10, 2019 Share Posted August 10, 2019 I'm in the same boat, no room. This was my solution. I just roll it into the closet when I'm done. Link to comment Share on other sites More sharing options...
Nickel City Dude Posted August 10, 2019 Share Posted August 10, 2019 I have limited space on my bench so I mount my presses on a piece of plywood and then install and remove them according to which press I want to use. When not in use I put them on a shelf I have in the loading room and this leaves a clear bench for other projects. I mounted a T nut to my bench and use a thumb screw when I have a press on the bench. Here is a press on the bench with the thumb screw holding it down. Here is what the thumb screw looks like in the bench. Note that when I don’t have a press on the bench the thumb screw if off in the tool rack. Here is the rack I use to store some of my presses. And this is what my bench looks like without any of my presses mounted on it. I hope this helps you. NCD Link to comment Share on other sites More sharing options...
The Original Lumpy Gritz Posted August 10, 2019 Share Posted August 10, 2019 Drill the bench top for your press, and use t-nuts. https://www.grainger.com/product/1XGH6?gclid=EAIaIQobChMI99f70KP54wIVxODICh2B8g2hEAQYBiABEgKr7_D_BwE&cm_mmc=PPC:+Google+PLA&ef_id=EAIaIQobChMI99f70KP54wIVxODICh2B8g2hEAQYBiABEgKr7_D_BwE:G:s&s_kwcid=AL!2966!3!50916713277!!!g!82128465477! OLG Link to comment Share on other sites More sharing options...
Sedalia Dave Posted August 10, 2019 Share Posted August 10, 2019 I use one of these Quick change press mounting system. One mount, countless uses. Use the storage rack to store the press I am not using. To secure the press to the bench I attached a 2X to the underside where the bolt holes are and installed these anchor nuts.E-Z Lok Threaded Insert, Zinc, Hex-Flanged, 1/4"-20 Internal Threads, 13mm Length Link to comment Share on other sites More sharing options...
Croc Holiday Posted August 10, 2019 Author Share Posted August 10, 2019 The cabinet is appealing for keeping things together. Mobility of the press being on a board is a good benefit though. at least both my initial solutions are represented Link to comment Share on other sites More sharing options...
Sedalia Dave Posted August 10, 2019 Share Posted August 10, 2019 3 minutes ago, The Original Lumpy Gritz said: Drill the bench top for your press, and use t-nuts. https://www.grainger.com/product/1XGH6?gclid=EAIaIQobChMI99f70KP54wIVxODICh2B8g2hEAQYBiABEgKr7_D_BwE&cm_mmc=PPC:+Google+PLA&ef_id=EAIaIQobChMI99f70KP54wIVxODICh2B8g2hEAQYBiABEgKr7_D_BwE:G:s&s_kwcid=AL!2966!3!50916713277!!!g!82128465477! OLG These work much better .E-Z Lok Threaded Insert, Zinc, Hex-Flanged, 1/4"-20 Internal Threads, 13mm Length Link to comment Share on other sites More sharing options...
J-BAR #18287 Posted August 10, 2019 Share Posted August 10, 2019 Are you limited to the garage? It’s much more comfortable to load in a spare bedroom, out of winter cold and summer heat, in controlled humidity and temperature conditions. My re-purposed student desk holds a lot of stuff: Link to comment Share on other sites More sharing options...
The Original Lumpy Gritz Posted August 10, 2019 Share Posted August 10, 2019 1 hour ago, Sedalia Dave said: These work much better .E-Z Lok Threaded Insert, Zinc, Hex-Flanged, 1/4"-20 Internal Threads, 13mm Length Tried those one time-Went back to what I posted as it has a larger head/flange. Won't pull into the wood, like those other ones did. OLG Link to comment Share on other sites More sharing options...
Randy Saint Eagle, SASS # 64903 Posted August 10, 2019 Share Posted August 10, 2019 My space is crowded and some day I need to clean it up but for now it works. Randy Link to comment Share on other sites More sharing options...
Shooting Bull Posted August 10, 2019 Share Posted August 10, 2019 1 hour ago, Tyrel Cody said: My Lee Turret press is mounted on a piece of 2×6 that's about a foot long and I clamp it to a workbenches. I did that so I could take a press to the range easily. ^This is exactly how I started off and it served me well as my primary press for many years. Still own it and take it to the range when I need to develop a new load. Easily transportable and clamps to a portable table for use. Link to comment Share on other sites More sharing options...
Trooper Ozzy Posted August 11, 2019 Share Posted August 11, 2019 Calibers loaded currently: 32 S&W, 9mm, 38 spl, 45 acp, 45 cowboy special, 45 colt, 45-70 Govt. Smokeless and BP. Lee Loadall on another board for 12 ga BP. Mec Jr on another board for .410 skeet shells. Link to comment Share on other sites More sharing options...
Croc Holiday Posted August 11, 2019 Author Share Posted August 11, 2019 20 minutes ago, Trooper Ozzy said: Calibers loaded currently: 32 S&W, 9mm, 38 spl, 45 acp, 45 cowboy special, 45 colt, 45-70 Govt. Smokeless and BP. Lee Loadall on another board for 12 ga BP. Mec Jr on another board for .410 skeet shells. How do you work the press while sitting on the stool? J/k... Link to comment Share on other sites More sharing options...
Trooper Ozzy Posted August 11, 2019 Share Posted August 11, 2019 19 minutes ago, Croc Holiday said: How do you work the press while sitting on the stool? Any cowboy worth his Spurs would throw the saddle on first...bareback is for injuns. Link to comment Share on other sites More sharing options...
Bugler Posted August 11, 2019 Share Posted August 11, 2019 I've known a number of folks in the same situation to use Black & Decker Workmate......saw this the first time when I was working with USAF personnel living in base quarters.....seemed to work well for them... Bugler Link to comment Share on other sites More sharing options...
Joe LaFives #5481 Posted August 11, 2019 Share Posted August 11, 2019 When I was in College some 40 years ago, I had a Lyman spar-t mounted to a board about 18"x24". The board was mounted to a 2" diameter pipe of about 3 feet long using a floor flange. I had another 18x24 board on the bottom again with the other end of the pipe in another floor flange. and I would sit and put my feet on the bottom board and load. Easy to store in a closet and I could sit and reload quite easily. Link to comment Share on other sites More sharing options...
Lazy Eeyour Posted August 11, 2019 Share Posted August 11, 2019 This is what I use, A bench grinder pedestal bolted to a piece of plywood for stability. I then use a 2x10 to join the reloader to pedestal with T-nuts. Think ahead and make sure all connections are recessed for a flat surface. Another idea is to connect the pedestal to a car wheel rim (weld/bolt). Additional fill the wheel rim with concrete. https://www.harborfreight.com/heavy-duty-bench-grinder-pedestal-68321.html Link to comment Share on other sites More sharing options...
Red Eye Jim Posted August 11, 2019 Share Posted August 11, 2019 I attached my 550 to this: https://www.amazon.com/Frankford-Arsenal-Reloading-Adjustable-Construction/dp/B00HTN98X6/ref=sr_1_13?crid=1F08SV26BVJ7N&keywords=reloading+bench&qid=1565504349&s=gateway&sprefix=reloading+b%2Caps%2C227&sr=8-13 In the theory that some day this is going to need to go in the RV. (We plan on spending up to 5 years living mostly out of the RV once we retire, however that may have to change if my MIL ends up living with us.) Link to comment Share on other sites More sharing options...
Ozark Huckleberry Posted August 11, 2019 Share Posted August 11, 2019 Started loading on a Spar-T that was mounted at an angle on a simple wooden bench about 3' long made of 2X6 lumber. I could sit on the bench and work the reloader. Moved up to a Dillon 450, then 550; both of them were mounted on a 2X6 fastened to the wall in the back corner of a garage. Next to it was a salvaged kitchen upper cabinet topped with a 2X6 and mounted so the top was level with the reloader bench. With the Dillon, the shallow cabinet and bench left plenty of room for getting the car in and out. Link to comment Share on other sites More sharing options...
Sedalia Dave Posted August 11, 2019 Share Posted August 11, 2019 9 hours ago, Bugler said: I've known a number of folks in the same situation to use Black & Decker Workmate......saw this the first time when I was working with USAF personnel living in base quarters.....seemed to work well for them... Bugler For a portable folding work bench this is by far the best solution. Especially if you can find one of the older all steel ones. Link to comment Share on other sites More sharing options...
Cypress Sam, SASS #10915 Posted August 11, 2019 Share Posted August 11, 2019 All things to excess! But when I started, I used a Lyman 310 tool that I kept in a kitchen drawer and a Belding and Mull powder measure that I had to go to a friends house to adjust because I didn’t have a powder measure. Link to comment Share on other sites More sharing options...
Kid Rich Posted August 11, 2019 Share Posted August 11, 2019 I went to a metal shop and got them to cut 1/4" aluminum plate in 6"X12" pieces, they are all permanently mounted to my presses. I mount them to the bench with a cordless electric drill. The holes for mounting to the bench are all drilled in the same place in the plates. It takes about 30 seconds to remove one press and mount another on the bench. kR Link to comment Share on other sites More sharing options...
Croc Holiday Posted August 11, 2019 Author Share Posted August 11, 2019 Thanks for all the input! For now I’ll mount it on the very fancy leftover IKEA shelf I have. Functional and classy! If they’re on my workbench too often I’ll ponder some of these. Link to comment Share on other sites More sharing options...
Captain Bill Burt Posted August 11, 2019 Share Posted August 11, 2019 15 hours ago, Randy Saint Eagle, SASS # 64903 said: My space is crowded and some day I need to clean it up but for now it works. Randy Looks like you snuck into my place, cleaned things up a bit, then took a picture. Link to comment Share on other sites More sharing options...
Three Foot Johnson Posted August 11, 2019 Share Posted August 11, 2019 My dad built this setup in an old sewing machine cabinet about 35 years ago. He's long since passed on, but my nephew still has it. Link to comment Share on other sites More sharing options...
Rowdy Ranger Rick Posted August 11, 2019 Share Posted August 11, 2019 I have a shared work space and bench for various hobbies. I mount presses to a small piece of plywood about 1/2" - 3/4" thick and various width/length depending on press and what type shelf I want to go with the press and room to store on shelf. I clamp the board down inside. My preference is to reload outside and clamp the press/board on this https://www.harborfreight.com/folding-clamping-workbench-with-movable-pegs-47844.html It is very sturdy, folds up, mobile, and cheap. It also serves as saw horse and outdoor workbench. I have similar shelf as Nickle City Dude to store presses on. I reload on my patio with a ceiling fan and a floor fan at each end. This keeps the air/powder/etc. moving. Even in Summer it is relatively comfortable to reload outside. If really tight on space, get a board about 2' x 4', clamp to the folding bench, clamp press to the big board, and you have a large work space. Table folds up, board stands up, press back on the shelf. Floor space is free again. RRR Link to comment Share on other sites More sharing options...
Dusty Devil Dale Posted August 11, 2019 Share Posted August 11, 2019 22 hours ago, Randy Saint Eagle, SASS # 64903 said: My space is crowded and some day I need to clean it up but for now it works. Randy Mine looks like that at times. My wife accuses me of needing to put on a harness and rope-up to get across my garage alive. Link to comment Share on other sites More sharing options...
Mo Likka Posted August 11, 2019 Share Posted August 11, 2019 https://www.homedepot.com/p/Husky-46-in-W-x-24-5-in-D-9-Drawer-Tool-Chest-Mobile-Workbench-with-Solid-Wood-Top-in-Black-H46MWC9XD/303101236 I use one of these for my Square Deal and MEC Sizemaster. Drawers are great for storage and it moves around easily when I need it to. Link to comment Share on other sites More sharing options...
The Original Lumpy Gritz Posted August 12, 2019 Share Posted August 12, 2019 12 hours ago, Cypress Sam, SASS #10915 said: All things to excess! But when I started, I used a Lyman 310 tool that I kept in a kitchen drawer and a Belding and Mull powder measure that I had to go to a friends house to adjust because I didn’t have a powder measure. Please give the details of that combo mill/lathe. OLG Link to comment Share on other sites More sharing options...
T-Square Posted August 12, 2019 Share Posted August 12, 2019 On July 15, 2019 at 6:07 PM, The Original Lumpy Gritz said: On August 9, 2019 at 9:41 PM, Matthew Duncan said: On August 10, 2019 at 7:03 PM, Randy Saint Eagle, SASS # 64903 said: My space is crowded and some day I need to clean it up but for now it works. Randy Randy, has your Doctor seen this? There is help available, and you shouldn't feel sad. (Joke - OMFG) Link to comment Share on other sites More sharing options...
T-Square Posted August 12, 2019 Share Posted August 12, 2019 Cypress Sam gets a ribbon, and a month at the Betty Ford Clinic ! Link to comment Share on other sites More sharing options...
Randy Saint Eagle, SASS # 64903 Posted August 12, 2019 Share Posted August 12, 2019 11 minutes ago, T-Square said: Randy, has your Doctor seen this? There is help available, and you shouldn't feel sad. (Joke - OMFG) His advise was to buy more stuff!! Randy Link to comment Share on other sites More sharing options...
T-Square Posted August 12, 2019 Share Posted August 12, 2019 I may make you my first Red Flag Law candidate, right after the Hillary Clinton Suicide investigations are complete, and someone goes to jail. Sarcasm added by the author for humor. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.