Chili Pepper Kid, SASS #60463 Posted May 18, 2019 Share Posted May 18, 2019 I've started to remove the spent primers with a hand de-primer then tumbling the brass. On my Dillon Square Deal, should I remove the pin that pokes out the primers on the 1st station or is there any benefit to leaving it in? Link to comment Share on other sites More sharing options...
Hillbilly Drifter Posted May 18, 2019 Share Posted May 18, 2019 I don't think it would hurt anything to leave it in. If there is any media from tumbling left in the flash hole it would clear that for you. Link to comment Share on other sites More sharing options...
Chili Pepper Kid, SASS #60463 Posted May 18, 2019 Author Share Posted May 18, 2019 28 minutes ago, Hillbilly Drifter said: I don't think it would hurt anything to leave it in. If there is any media from tumbling left in the flash hole it would clear that for you. Howdy pard. Good point, I hadn't thought of that. Link to comment Share on other sites More sharing options...
Tequila Shooter Posted May 18, 2019 Share Posted May 18, 2019 I'd leave it in. As said it won't hurt and just in case you missed a primer it'll pop it out. I wet tumble and have had small pins get caught in the primer pocket. Link to comment Share on other sites More sharing options...
El Hombre Posted May 18, 2019 Share Posted May 18, 2019 Leave it in Link to comment Share on other sites More sharing options...
The Original Lumpy Gritz Posted May 18, 2019 Share Posted May 18, 2019 Leave it-Better to have and not need it......... OLG Link to comment Share on other sites More sharing options...
Old Man Graybeard Posted May 18, 2019 Share Posted May 18, 2019 If you are going to prime on the press...shouldn’t make a difference. I decap on a single stage press and hand prime...so I take the decamping pin out of the die. Link to comment Share on other sites More sharing options...
Dead Eye Jake Posted May 18, 2019 Share Posted May 18, 2019 As stated by Hillbilly Drifter it will clear the flash hole if you're dry tumbling. I punch my primers out of the black powder brass before tumbling and the pin clears out any media stuck in the flash hole. Leave it in. Link to comment Share on other sites More sharing options...
Painted Mohawk SASS 77785 Posted May 19, 2019 Share Posted May 19, 2019 21 hours ago, Chili Pepper Kid, SASS #60463 said: I've started to remove the spent primers with a hand de-primer then tumbling the brass. On my Dillon Square Deal, should I remove the pin that pokes out the primers on the 1st station or is there any benefit to leaving it in? Hi Chili I'm just curious as to the advantage you see in depriming by hand ? Link to comment Share on other sites More sharing options...
Flatwater Monte Posted May 19, 2019 Share Posted May 19, 2019 1 hour ago, Painted Mohawk SASS 77785 said: Hi Chili I'm just curious as to the advantage you see in depriming by hand ? I can't speak for Chilli Pepper, but my assumption is that he likes to have the primer pocket exposed to the timbling media to allow it a chance to get cleaned. I have done it both ways. Deprimed and tumbled or tumbled and deprimed. I have started depriming and tumbling every fourth reload now. I am also using an rcbs case prep station to use a carbon scraper on the primer pockets at that point to just help clean them out. I actually think that the scrapper gets the pocket cleaner than tumbling does. On top of it all, I am reloading for 4, so the time savings of not depriming first everytime keeps me mildly sane. Link to comment Share on other sites More sharing options...
Chili Pepper Kid, SASS #60463 Posted May 19, 2019 Author Share Posted May 19, 2019 4 hours ago, Painted Mohawk SASS 77785 said: Hi Chili I'm just curious as to the advantage you see in depriming by hand ? Actually the reason I've started de-priming is last year the 1st station (12 yr old Dillon Square Deal)stopped poking out the old primer reliably. Out of a 100 primers 3-5 would not be removed. This would disrupt the flow of loading. I called Dillon and they said to replace the pin and they sent me a couple. They told me it had most likely mushroomed slightly and was poking the primer out then pulling it back in. It didn't work so I called Dillon and they said to take a file and file off the pin to make it like a truncated cone. This still didn't work and was getting worse 10-12 per 100. I called Dillon back and they blamed the way primers are made now. So I did a search for hand de-primers and found high marks for the Harvey De-primer https://harveydeprimer.com. I got one and have found I like de-priming first because the primer pocket is getting cleaned so the new primer seats easier. I can de-prime a monthly match worth of brass (120) in 15 minutes. Link to comment Share on other sites More sharing options...
The Original Lumpy Gritz Posted May 19, 2019 Share Posted May 19, 2019 You hands are gonna get tired of the hand depriming. Call Dillon again and maybe send the press in for rebuild. Your hands-Your choice........ OLG Link to comment Share on other sites More sharing options...
Too Tall Bob Posted May 19, 2019 Share Posted May 19, 2019 Out of curiosity - have you checked to see if your sizing/de-priming die may have backed out a little bit? Also, you might check to see if the shell plate is set tight enough. Your sizing die should come right to the top pf the shell plate at position one at full stroke. There should be no up and down slop in the shell plate. Good luck and let us know what cures you problem Link to comment Share on other sites More sharing options...
Cheyenne Ranger, 48747L Posted May 19, 2019 Share Posted May 19, 2019 taking a trip down the rabbit hole . . . I remove my tool head and dies, replace with head that only has depriming pin (4 bolts out and in) 3 bolt out to remove primer assembly now I can run my 5 minute dry tumbled brass through the machine to deprime. Don't have to remove the brass as they travel around the shell plate and drop in the bin. I figure it cuts my work in half not having to remove the brass when done reverse the tool head and primer processes --takes less than 5 minutes to do this either coming or going electric drill with all wrench bit also is a big help Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.