Deuce Stevens SASS#55996 Posted October 8, 2018 Share Posted October 8, 2018 I’m really enjoying all the information available on the current wire. Reminds me of old times. What is your favorite 12ga recipe for CAS?( Please hold the preaching and hand wringing). I’ll start 14.6 gr. of Clay Dot. 7/8 oz in a Lightning spreader wad and a STS/Gun Club hull. Link to comment Share on other sites More sharing options...
War Grizzly Posted October 8, 2018 Share Posted October 8, 2018 15.6 gr clays (mec 28 bushing) Cheddite primer 7/8 oz 7.5 shot Waa12l wad Gun club hull Mec Grabber loader I also load the same in AA hulls but my cimmaron 1878's shuck the Remington hulls better. Link to comment Share on other sites More sharing options...
G W Wade Posted October 8, 2018 Share Posted October 8, 2018 15.6 / 16.0 promo claybuster CB0175 3/4 oz Cheddite primer WW AA hull This load is snappy. Hammers targets hard due to velocity, but softer because of 3/4 oz payload. Straight rom Claybuster data sheet provided with wads. GW Link to comment Share on other sites More sharing options...
Roscoe Regulator Posted October 8, 2018 Share Posted October 8, 2018 Win AA hull, Extralite powder, MEC # 25, 7/8 oz. #8 chilled shot, W209 primer, grey wad WAA12L or equivalent. That bushing # yields 13 grains +-.3. I find I have to keep powder bottle topped off to maintain drop yields. Never been a problem shooting them. I am now transitioning to some Fiocchi targets calling for Lightning wads and a 6 point crimp. I am loading one box and will see how they shoot. I have been retiring my Win AA hulls as having been reloaded enough times and all looking like culls now. I may start a new batch of firing new shells, once the reloads in service get fired off and hulls discarded. Link to comment Share on other sites More sharing options...
Jackson Rose, SASS #45478 Posted October 8, 2018 Share Posted October 8, 2018 Gun club hull, 60 gr. of 2f, nitro card and 1/2 inch cushion wad, 1 1/8 of 7 1/2s. Link to comment Share on other sites More sharing options...
Colorado Coffinmaker Posted October 8, 2018 Share Posted October 8, 2018 MagTech All Brass Hulls, 50Gr APP 3f, 10Ga plastic wad cut for a 1oz payload. Link to comment Share on other sites More sharing options...
Chief Rick Posted October 8, 2018 Share Posted October 8, 2018 Win AA hull 14.4 gr Clays (MEC 26 bushing) 7/8 oz shot Claybuster CB0178-12 (WAA12L) Link to comment Share on other sites More sharing options...
The Original Lumpy Gritz Posted October 8, 2018 Share Posted October 8, 2018 Just about any 12ga hull, except AA. 17.5gn Unique and 3/4-1oz of shot. Any SG primer. Very low in recoil- OLG Link to comment Share on other sites More sharing options...
Rye Miles #13621 Posted October 8, 2018 Share Posted October 8, 2018 14.5 grains of Universal Clays, a WWA12 wad and 1 oz of #7 shot all stuffed in a AA Win hull. Link to comment Share on other sites More sharing options...
Yusta B. Posted October 8, 2018 Share Posted October 8, 2018 Buckerette load: AA hull Claybuster CB0178-12 wad Win 209 7/8 oz 9 gr Promo - MEC #15 bushing Gets a bit tired in the cold. Takes down all the KD's at Bar 3 if aimed. Link to comment Share on other sites More sharing options...
Eyesa Horg Posted October 8, 2018 Share Posted October 8, 2018 AA hull or Rem. STS hull Claybuster CB0178-12 wad Win 209, Fed. 209 or cheddite 209 primer 7/8 oz #8 shot 14.5gn. 700X powder Link to comment Share on other sites More sharing options...
Null N. Void Posted October 8, 2018 Share Posted October 8, 2018 1 ounce of 7.5. Any wad for 1 ounce. Remington Nitro hull. 14 grains of Promo. Winchester Primer (works better in my pump) Link to comment Share on other sites More sharing options...
Southpaw Gringo, SASS # 74217 Posted October 8, 2018 Share Posted October 8, 2018 STS or AA hulls 7/8oz reclaimed shot WAA12 grey wad (claybuster) 15grns of Clays powder---MEC powder bushing #28 any 209 primer. I like CCI Link to comment Share on other sites More sharing options...
Smoky Pistols Posted October 8, 2018 Share Posted October 8, 2018 Okay, I need clarification! I love the info here, but a few months back, when I posted some load data (and I was only asking a question) at least six people jumped me and shouted "Illegal". What gives now? Link to comment Share on other sites More sharing options...
Southpaw Gringo, SASS # 74217 Posted October 8, 2018 Share Posted October 8, 2018 Just now, Smoky Pistols said: Okay, I need clarification! I love the info here, but a few months back, when I posted some load data (and I was only asking a question) at least six people jumped me and shouted "Illegal". What gives now? They lifted the no reloading recipe rule. . Link to comment Share on other sites More sharing options...
Totes Magoats Posted October 8, 2018 Share Posted October 8, 2018 STS Hull 13.9 grains Clays Federal primer WAA12L grey hull (claybusters) 7/8oz of 7.5 or 8 shot Totes Link to comment Share on other sites More sharing options...
Smoky Pistols Posted October 8, 2018 Share Posted October 8, 2018 28 minutes ago, Southpaw Gringo, SASS # 74217 said: They lifted the no reloading recipe rule. . Oh, okay. I figured there was something I was unaware of. Good deal. Continue on as if I've said nothing then! Link to comment Share on other sites More sharing options...
Hawkeye Kid Posted October 8, 2018 Share Posted October 8, 2018 2.8 cc or 3.1 cc 2f or 3f. Black or APP. Win AA Red wad, 1 1/8oz of 7.5 or 8 shot;federal primer WinLite. 13.6g. 1oz shot. WinAA hulls pink wad, Federal Primers. Looking for a similar load using Clays. WinLite is about gone. Link to comment Share on other sites More sharing options...
Driftwood Johnson, SASS #38283 Posted October 8, 2018 Share Posted October 8, 2018 6 hours ago, Deuce Stevens SASS#55996 said: ( Please hold the preaching and hand wringing) Never let it be said that I can't take a hint. My favorite CAS 12 Gauge load is 4.3CC (about 66 grains) of Schuetzen FFg, a 1/8" Circle Fly Over Powder wad, a 1/2" Circle Fly Compression wad, 1 1/8 ounces of #8 shot, a Circle Fly Over Shot Card, a Winchester 209 Primer, all stuffed into a Remington STS hull. Link to comment Share on other sites More sharing options...
Guest Texas jack Black SASS#9362 Posted October 8, 2018 Share Posted October 8, 2018 My gamer load, 1 1/8 of #9 shot with a spreader wad slit, over a charge of Red Dot. Works VERY well on knock downs and especially on flyers . Link to comment Share on other sites More sharing options...
Roscoe Regulator Posted October 8, 2018 Share Posted October 8, 2018 This may be the place for me to mention that once I used up my "magnum" #8 shot I went to "chilled" as softer and less likely to blowback on the gallery. Link to comment Share on other sites More sharing options...
Sgt. Hochbauer, SASS #64409 Posted October 8, 2018 Share Posted October 8, 2018 If I am feeling industrious... using AA hulls trimmed any 209 primer I use a 1oz square load. After trimming and priming 1oz dipper of goex 2f 1/8 in nitro card and fiber wad (Circlefly) 1oz of 7.5 or 8 shot topped off with a overshot card..then roll crimp. Sgt H Link to comment Share on other sites More sharing options...
Rooster Ron Wayne Posted October 9, 2018 Share Posted October 9, 2018 9 hours ago, The Original Lumpy Gritz said: Just about any 12ga hull, except AA. 17.5gn Unique and 3/4-1oz of shot. Any SG primer. Very low in recoil- OLG You beat me too it again lol. Same load for me . Rooster Link to comment Share on other sites More sharing options...
Rowdy Ranger Rick Posted October 9, 2018 Share Posted October 9, 2018 Rotator cuff surgery earlier this year, now back shooting... AA or STS hulls, Remington or Winchester 209 primers, 7/8 oz. shot, WAA12L grey wads. MEC 9000 #25 bushing, measured 13.4 gr. Red Dot...but also Clays or Clay Dot without changing bushing. Shoulder is happy. Recently loaded IMR Red with same bushing, measured 14.4 gr. Shooting that (with 13.4 Red Dot, for comparison) at this coming weekend match. Spray finished shells with Armor All, wipe off excess with paper towel, shiny and slick. SASS Wire is a WHOLE LOT more fun now with reloading data. RRR Okay, don't know if anyone was planning to check back on Red Dot and IMR Red comparison. Shot 13.4 gr. Red Dot left barrel and 14.4 gr. IMR Red right barrel in my S x S 12 g., 6 stages (loaded all with #25 bushing). Maybe an occasional slight smidge more umpf sound in right barrel, but not noticeable on my repaired shoulder. Supposedly, IMR Red was comparable sub for Red Dot, but for same volume it is about 1 gr. heavier. Link to comment Share on other sites More sharing options...
Hells Comin Posted October 9, 2018 Share Posted October 9, 2018 9.1 grains alliant extra-lite -Winchester hulls- lightning wads 1-1/6oz. Of #8's- fed 209's. Link to comment Share on other sites More sharing options...
Griff Posted October 9, 2018 Share Posted October 9, 2018 Once fired, and once fired ONLY AA hulls, Federal 210 primers, (or Winchester, I don't care), Claybuster CB1138-12 wad, however much Goex 2F fits in a MEC #43 bushing and one oz of #9 shot!. Key to this load is keeping the right amount of pressure on the wad as you dump the shot... too little pressure and the shot doesn't crimp well, too much and you have a hole in the center of the crimp and shot dribbles out... Otherwise... Winchester AA12FL8. Link to comment Share on other sites More sharing options...
Deuce Stevens SASS#55996 Posted October 9, 2018 Author Share Posted October 9, 2018 8 hours ago, Hells Comin said: 9.1 grains alliant extra-lite -Winchester hulls- lightning wads 1-1/6oz. Of #8's- fed 209's. How clean is thst load? Are you loading on a Mec and if so what bushing? I would assume that it is sub sonic. Interesting Link to comment Share on other sites More sharing options...
Boomstick Bruce Posted October 9, 2018 Share Posted October 9, 2018 $5.50 a box at Wally...lol.. Link to comment Share on other sites More sharing options...
Marshal TKD, Sass # 36984L Posted October 9, 2018 Share Posted October 9, 2018 12.5 grains of clays 1 oz of shot AA hulls clayduster wad Link to comment Share on other sites More sharing options...
Cheatin Charlie Posted October 9, 2018 Share Posted October 9, 2018 23 hours ago, The Original Lumpy Gritz said: Just about any 12ga hull, except AA. 17.5gn Unique and 3/4-1oz of shot. Any SG primer. Very low in recoil- OLG What wad would work in Remington STS hull with this load with 3/4 oz shot? Thanks Link to comment Share on other sites More sharing options...
Hells Comin Posted October 9, 2018 Share Posted October 9, 2018 2 hours ago, Deuce Stevens SASS#55996 said: How clean is thst load? Are you loading on a Mec and if so what bushing? I would assume that it is sub sonic. Interesting Deuce I'm loading on a Dillion SL900. This load is super clean even with the lite charge and No unburned powder At All. Yes it is a subsonic load as I recall it's a little less than 900 fps Recoil feels similar to a Featherlite, but with a lot more bb's. Link to comment Share on other sites More sharing options...
The Original Lumpy Gritz Posted October 9, 2018 Share Posted October 9, 2018 10 minutes ago, Cheatin Charlie said: What wad would work in Remington STS hull with this load with 3/4 oz shot? Thanks Even though they are marketed for WW. I had good luck in Fed and Remmy 12ga hulls. https://www.powdervalleyinc.com/product/claybuster-12-ga-win-3-4-oz/ I use this for my 1oz SASS 12ga loads https://www.powdervalleyinc.com/product/claybuster-12-ga-rem-tgt12/ Stopped load'n 3/4oz shot loads because of stubborn knock downs. OLG Link to comment Share on other sites More sharing options...
Jabez Cowboy,SASS # 50129 Posted October 9, 2018 Share Posted October 9, 2018 4.3 CC of Goex 3F and the same volume of shot, in a 12 ga. hull with what ever plastic wad that gives the right crimp height in the hull used ... 3.4 CC of Goex 3F and 1 oz of shot, in a 16 ga. hull with the plastic that gives the right Crimp Height in the hull of the moment .... I use Winchester or CCI , 209s .... I buy mostly Federal ammo in 16 ga. to get hulls for using with Black .... Jabez Cowboy Link to comment Share on other sites More sharing options...
Hoot Hamilton Posted October 9, 2018 Share Posted October 9, 2018 Rem STS hulls, once fired for big matches, twice + for monthlies. 13.0 g Red Dot Fed 209 Primer WAA 12L grey wad 7/8 ounce #8 Loaded on a MEC9000 for SKB100s Link to comment Share on other sites More sharing options...
VICIOUS, SASS#8014 Posted October 10, 2018 Share Posted October 10, 2018 Rem STS hull 3/4 ounce of # 8 shot claybuster pink wad CBO 175-12 Red Dot 16 grains Cheddite primer Look at claybuster web page for full 3/4 ounce loads. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.