Doc Coles SASS 1188 Posted September 12, 2018 Share Posted September 12, 2018 I have a 3rd gen sheriffs model that has the non-removable bushings. One of them has too much spacing and the front of the cylinder drags on the back of the barrel. One option is to simply replace the bushing with a new one, or remove the bushing and shim it. Another option is to go the whole hog and convert the cylinder to take a removable bushing, which is more work but easier to deal with in the long run. I would have to do two cylinders as this gun has both 44spl and 44-40 cylinders. Has anyone tackled this job? Or does anyone have a recommendation on who can do the bushing conversion? Link to comment Share on other sites More sharing options...
Turquoise Bill, SASS #39118 Posted September 12, 2018 Share Posted September 12, 2018 Bob James is the man, he can be contacted at Legendary Guns in Phoenix, AZ. TB Link to comment Share on other sites More sharing options...
Doc Coles SASS 1188 Posted September 12, 2018 Author Share Posted September 12, 2018 8 minutes ago, Turquoise Bill, SASS #39118 said: Bob James is the man, he can be contacted at Legendary Guns in Phoenix, AZ. TB That is interesting. I spent some time there the last time I was in Phoenix. I will give them a call. Link to comment Share on other sites More sharing options...
H. K. Uriah, SASS #74619 Posted September 12, 2018 Share Posted September 12, 2018 I had a similar problem with one of my Sheriff's models. The .44 Special cylinder worked just fine, but the .44-40 cylinder was overall length just a tad too long. I took it to a local smith who put the cylinder on a lathe and he ground off maybe a thousandth of an inch or two off the bushing and then everything worked fine. But sounds like your problem is the opposite of mine... Not sure of the solution. Link to comment Share on other sites More sharing options...
Doc Coles SASS 1188 Posted September 12, 2018 Author Share Posted September 12, 2018 Yeah, you had the opposite problem. I could run a shim on the bushing, which is a pain, I could replace the stubby 3rd gen pressed in bushing/spacer with a longer one, I could have the cylinder cut to take the standard long bushing, or I could just replace the cylinder with a later 3rd gen cylinder (though it would be nice to keep the serial numbered ones) I don't see the short press in 3rd gen bushings for sale anywhere, though they would be simple to make on the lathe. Not sure how to get the original one out. Link to comment Share on other sites More sharing options...
levi littleton Posted September 12, 2018 Share Posted September 12, 2018 Typically just $60 to cut the cylinder if you can fit your own bushing. Easy enough to do. Link to comment Share on other sites More sharing options...
The Original Lumpy Gritz Posted September 12, 2018 Share Posted September 12, 2018 I have used one of these for many years, with great results. https://www.brownells.com/gunsmith-tools-supplies/handgun-tools/gas-system-tools/single-action-gas-ring-stretcher-prod1029.aspx OLG Link to comment Share on other sites More sharing options...
levi littleton Posted September 12, 2018 Share Posted September 12, 2018 Surprised Wild West guns can't do it for you. Link to comment Share on other sites More sharing options...
Doc Coles SASS 1188 Posted September 13, 2018 Author Share Posted September 13, 2018 8 hours ago, levi littleton said: Surprised Wild West guns can't do it for you. I have not had good luck having them work on SAAs. I would rather send it to someone who does the work all the time. Link to comment Share on other sites More sharing options...
hearsedriver Posted September 18, 2018 Share Posted September 18, 2018 I tackled this job a couple of days ago. Its easy and cheap to do. A package of 3 bushings can be bought for $17.95 here: http://parts.bowenclassicarms.com/index.php?main_page=product_info&cPath=8&products_id=53 Removing the old bushing is simple if you are replacing it. Simply tap the hole to 5/16-24 about 1/8" deep. Dont go too deep or you will be into the cylinder itself. I went a little deep on mine. Its not a big deal but now I have a s mall gap between the bushing and cylinder bore. The bushing sits in a counterbore so, not a big deal. Leave the tap inserted and tap the bushing out with a 1/4" brass rod from the other end. Instructions are included with the bushings. I faced my new bushing off with a hand file and finished on a flat surface with 400 grit sandpaper. Just make sure you keep the face of the bushing true to the cylinder. A lathe would be much better but, I was able to achieve good results by hand. Link to comment Share on other sites More sharing options...
August West, SASS #45079 Posted September 18, 2018 Share Posted September 18, 2018 Shims that are for just the problem/issue you describe. Even if you go to all the work to install a cylinder bushing, you may still end up having to use these shims. Link to comment Share on other sites More sharing options...
Griff Posted September 19, 2018 Share Posted September 19, 2018 I had my two early 3rd gens SAAs converted to 2nd gen cylinders years ago. I got recommendations for several smiths... including Bob James, Bowen among others, (some of whom are no longer in business). I ended up having 'em done by Oglesby & Oglesby... Bill Oglesby himself did them... and I've heard since that I was lucky, as other have said they didn't fare too well with their work. Another that is highly acclaimed is Alan Harton in Houston, (713) 772, 8314. Link to comment Share on other sites More sharing options...
Doc Coles SASS 1188 Posted September 19, 2018 Author Share Posted September 19, 2018 4 hours ago, August West, SASS #45079 said: Shims that are for just the problem/issue you describe. Even if you go to all the work to install a cylinder bushing, you may still end up having to use these shims. Honestly, this issue is the sign of sloppy workmanship by Colt when they built the gun. Colt did some pretty bad work at different times in the 70s and 80s. This bushing has 7 thousandths of play, when the shop manuals call for essentially no play. Aside from the issue of the cylinder rubbing on the barrel, it also means the headspace is excessive. shims are a work-around at best. The solution is to do the job right. I would be very disappointed if I needed to use them after any repair. Link to comment Share on other sites More sharing options...
Doc Coles SASS 1188 Posted September 19, 2018 Author Share Posted September 19, 2018 16 hours ago, hearsedriver said: I tackled this job a couple of days ago. Its easy and cheap to do. A package of 3 bushings can be bought for $17.95 here: http://parts.bowenclassicarms.com/index.php?main_page=product_info&cPath=8&products_id=53 Removing the old bushing is simple if you are replacing it. Simply tap the hole to 5/16-24 about 1/8" deep. Dont go too deep or you will be into the cylinder itself. I went a little deep on mine. Its not a big deal but now I have a s mall gap between the bushing and cylinder bore. The bushing sits in a counterbore so, not a big deal. Leave the tap inserted and tap the bushing out with a 1/4" brass rod from the other end. Instructions are included with the bushings. I faced my new bushing off with a hand file and finished on a flat surface with 400 grit sandpaper. Just make sure you keep the face of the bushing true to the cylinder. A lathe would be much better but, I was able to achieve good results by hand. Thanks for the source for the bushings. I could not find them. Sounds like a very simple job to replace them. I even have access to a lathe to get the play setup properly. For the price I think I will give this a try. Link to comment Share on other sites More sharing options...
hearsedriver Posted September 19, 2018 Share Posted September 19, 2018 Good luck Doc! With a lathe, it will be a piece of cake! Link to comment Share on other sites More sharing options...
Oklahoma Dee Posted September 19, 2018 Share Posted September 19, 2018 3 hours ago, Griff said: Another that is highly acclaimed is Alan Harton in Houston, (713) 772, 8314. I agree. Alan Harton of Single Action Service, located in Houston, Texas. Call him and ask your question(s). He will tell you the steps and the pitfalls if any. Link to comment Share on other sites More sharing options...
Doc Coles SASS 1188 Posted September 19, 2018 Author Share Posted September 19, 2018 1 hour ago, hearsedriver said: Good luck Doc! With a lathe, it will be a piece of cake! Thanks, as you say, fitting bushings is straight forward with a lathe. I just did one for a 2nd gen and had no discernible play when it was done. Link to comment Share on other sites More sharing options...
Colorado Coffinmaker Posted September 19, 2018 Share Posted September 19, 2018 Id' vote Alan Harton. Link to comment Share on other sites More sharing options...
ShadowCatcher Posted September 20, 2018 Share Posted September 20, 2018 http://www.peacemakerspecialists.com/smithing.html Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.