Jump to content
SASS Wire Forum

Archived

This topic is now archived and is closed to further replies.

Hoss

Dillon - lee case feeder

Recommended Posts

a while back somebody posted about a way to use a Lee case collator on a Dillon 650. I searched, but no luck. Seemed like it was a pretty regular poster.

 

Anyways, I bought a Dillon, but I don't have the overhead space for the case feeder where I currently have my press. I'm going to try to make the Lee case collator/feeder work, I found a guy that 3D prints some sort of adapter, but was hoping for more info   Anybody have any info????

Share this post


Link to post
Share on other sites

The Bunkhouse master may disapprove, but, a Sawsall can work wonders on head room.:P

Share this post


Link to post
Share on other sites

I’ve got two 650s. I hand load my cases into the tube about thirteen at a time. It’s kind of self-regulating and gives me a chance to check other things. I can still load about 200-250 an hour.

Share this post


Link to post
Share on other sites

With the Dillon Case Feeder, can't the support pipe and plastic feed tube be shortened?  Just wondering.

Share this post


Link to post
Share on other sites
3 hours ago, Hoss said:

a while back somebody posted about a way to use a Lee case collator on a Dillon 650. I searched, but no luck. Seemed like it was a pretty regular poster.

 

Anyways, I bought a Dillon, but I don't have the overhead space for the case feeder where I currently have my press. I'm going to try to make the Lee case collator/feeder work, I found a guy that 3D prints some sort of adapter, but was hoping for more info   Anybody have any info????

It was me Hoss, I make a little bracket works like a charm and costs only $15.00  shipped.5afa0bb0e9346_DilleeCasefeeder1.thumb.JPG.8e9c10365c4730289cd89c2acd629598.JPG5afa0bd228b7c_DilleeCaseFeeder2.thumb.JPG.cd8ac7266573f6744c1d259aa09a957b.JPG

Share this post


Link to post
Share on other sites

Yea, I don't think the Lee case feeder with all that tubing is going to solve his height problem.  

 

I just measured my Dillon 650 case feeder and it only sticks up 10 1/2" above the top of the powder hopper.  Of course, you would need some room to put cases in and change out the shell feeder plate.

Share this post


Link to post
Share on other sites
48 minutes ago, Badlands Bob #61228 said:

Yea, I don't think the Lee case feeder with all that tubing is going to solve his height problem.  

 

I just measured my Dillon 650 case feeder and it only sticks up 10 1/2" above the top of the powder hopper.  Of course, you would need some room to put cases in and change out the shell feeder plate.

My problem is towards the rear of my bench, the front has plenty of room. I think.... the Lee case collator will work if I can get it hooked up. And save $239! 

Share this post


Link to post
Share on other sites
14 hours ago, Jackaroo, # 29989 said:

It was me Hoss, I make a little bracket works like a charm and costs only $15.00  shipped.5afa0bb0e9346_DilleeCasefeeder1.thumb.JPG.8e9c10365c4730289cd89c2acd629598.JPG5afa0bd228b7c_DilleeCaseFeeder2.thumb.JPG.cd8ac7266573f6744c1d259aa09a957b.JPG

Jackaroo,

 

send me one! I sent you a PM

Share this post


Link to post
Share on other sites

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.