Charlie MacNeil, SASS #48580 Posted October 4, 2013 Share Posted October 4, 2013 What's the secret code to removing the bolt cross pin in a Uberti 73? I'm trying to change out the firing pin of my 73 for one of Pioneer Gun Works' extended firing pins. I apparently have a new enough rifle that it has the funky little plate to hold the firing pin extension in place. According to Marauder's website, "The second method (in really old rifles OR in the newestmodels) uses the forward pin that holds the links. In this model, thepin is removable, just slide it out. Then there is an odd shaped piecethat slides up into the breech block that holds in the firing pinextension. Then you may remove the firing pin extension, firing pin andspring." However, therein lies the rub. Mine doesn't just slide out. It seems to be pretty firmly attached to the breech block. Any suggestions for removing it? Thanks! Link to comment Share on other sites More sharing options...
richie reno Posted October 4, 2013 Share Posted October 4, 2013 had to use a brass hammer on mine , back it up on the other side with a small socket , it came out very hard Link to comment Share on other sites More sharing options...
Captain Clark Posted October 4, 2013 Share Posted October 4, 2013 Use a BRASS punch and definitely support the underside / backside when you drive it out. The pin is tight in the side retaining plate by design, but not extreme.It's not as scary as it seems.I place a piece of hard wood under the bolt as support, but a small socket like Richie Reno suggested could work also. After the pin is out, then the side plate will slide out of the cut in the assembly. The side retaining plate that the pin passes thru does go back in the same as it comes out...IE it has a front / back angle so keep track as it will make it easier to reassemble! Link to comment Share on other sites More sharing options...
Rance - SASS # 54090 Posted October 4, 2013 Share Posted October 4, 2013 If ya care ta do so... When I had mine apart.. I tooks some very fine 600 grit sand paper and wrapped it around a small dowel... (or drill bit) Put it in the hole of the bolt and spun it a few times.. That sanded the hole out (ever so slightly) just enough to make the pin slide in and out without the use of a hammer.. Rance Thinkin' I didn't like the idea of beaten' it out with a hammer fer future disassembly.. Oh yeah.. I ain't a gunsmith.. Link to comment Share on other sites More sharing options...
Monco Posted October 4, 2013 Share Posted October 4, 2013 had to use a brass hammer on mine , back it up on the other side with a small socket , it came out very hard +1 Link to comment Share on other sites More sharing options...
Butch McGie, SASS#71758 Posted October 4, 2013 Share Posted October 4, 2013 This may sound stupid, but triple check that u put it back in. That pin is really important - u don't want to have to shoot with an eyepatch. Link to comment Share on other sites More sharing options...
Rance - SASS # 54090 Posted October 4, 2013 Share Posted October 4, 2013 Butch.. On this style of bolt the pin he's talkin' about is the pin that holds the front toggle link.. Rance Thinkin' it'd be a little hard ta cycle/lever/shoot without it.. But again... I ain't a gunsmith. Link to comment Share on other sites More sharing options...
Mad Dog Jack, SASS #77862 Posted October 4, 2013 Share Posted October 4, 2013 When cleaning my 73 after removing the toggle links the pin falls right out, I have to be careful not to lose it or the tab that retains the two parts of the bolt. Anyone know when the change took place from this way to the solid pin? And are the bolts interchangable? Link to comment Share on other sites More sharing options...
Rance - SASS # 54090 Posted October 4, 2013 Share Posted October 4, 2013 Mad Dog... They made the change about oooohhh... maybe 3-4 years ago.. They said the new bolt style is safer.... The whole thing (bolt and extention) will interchange but... not just the bolt.. The bolt extention.. (thingy that pushes the hammer back) is made to allow fer that little piece that falls out when yer pin falls out... Old model has a tiny little pin... that goes into the tiny little hole the old bolt extention has. Rance Thinkin' that's the best I can do Link to comment Share on other sites More sharing options...
Mad Dog Jack, SASS #77862 Posted October 4, 2013 Share Posted October 4, 2013 Well, I'm confused. I've had mine for 4 years or there abouts and got it from someone here on the Wire that had it. I didn't know there was a difference until I watched a guy clean his a the range last month and he said I have the "old type" and that the ones with the large pins solid,and the small pin retaining the two parts of the bolt together were the "new type". Kida a PITA to have to keep an eye out for small part when cleaning, but I'm used to it. The first time was kinda exciting though. Thinking the little pin could be a PITA if I needed to get to the firing pin too... Link to comment Share on other sites More sharing options...
Rance - SASS # 54090 Posted October 4, 2013 Share Posted October 4, 2013 Mad Dog... Thinkin' he just made a little mistake... That big pin that slides through the flat retainer (that ya gotta' watch out fer) ... that holds the bolt extention to the bolt... that the front of the toggle links slip over Is the new style.... They were sayin' that little tiny pin ya had ta drive out with little bitty punch was a weak point.. and dangerous... Rance Thinkin' that's all the knowledge I got.. but.. thinkin' ya got the new style... Mighta' been ooooohhh... 4-5-6 years ago they made the change Told ya I wasn't a gunsmith Link to comment Share on other sites More sharing options...
Mad Dog Jack, SASS #77862 Posted October 4, 2013 Share Posted October 4, 2013 Thanks for the info Rance, just went out to look at the date code on the rifle, but it was to much trouble to take off the forearm to check, and finding the codes online was not cooperating either....must be meant for me to do something else with my time today Link to comment Share on other sites More sharing options...
Cowboy Rick, SASS #49739L Posted October 4, 2013 Share Posted October 4, 2013 Ran across my first one the other day. With the right size brass punch, it's not too hard to deal with. CR Link to comment Share on other sites More sharing options...
BLACKFOOT SASS #11947 Posted October 4, 2013 Share Posted October 4, 2013 The fit of the pin seems to run all over the scale. Some are loose fit, some thumb press fit, some tap with hammer fit and some a fairly tight fit. Lafitte Link to comment Share on other sites More sharing options...
Boggus Deal #64218 Posted October 4, 2013 Share Posted October 4, 2013 I was under the impression the change was somewhere around 2008. Link to comment Share on other sites More sharing options...
KingSnake Posted October 4, 2013 Share Posted October 4, 2013 I am not a gunsmith, but I have been a machinist for more years than I care to mention. I have had folks bring their new style bolts for me to press out the pin on an arbor press. I then open the hole to a slip fit so they can disassemble it themselves in the future. Both my rifles that had the new style bolts were already slip fits. I was gonna say something about Italian machinsts, but I wouldn't want to offend anyone. Link to comment Share on other sites More sharing options...
Judge Gardner Posted October 4, 2013 Share Posted October 4, 2013 You can make a tool for this a 1 inch x 1 inch metal block one side flat and the other side with a 1/4 hole. The hole side is for removing the pin and the flat side putting it in and will come out to the right depth. Works good!!!!! Link to comment Share on other sites More sharing options...
Monco Posted October 4, 2013 Share Posted October 4, 2013 I was under the impression the change was somewhere around 2008. That's the same impression I find myself under. Guess Uberti decided to use the same method that Winchester used to retain the firing pin/firing pin extension after determining that the cheaper method was more dangerous. Wonder if some poor sole had to pay the price with a patch over the eye to figure that one out. First time I did it I used my press but have used the hammer, punch, and supporting socket method since. Much easier than supporting the rifle and related tools in the press while pumping the press lever. Link to comment Share on other sites More sharing options...
Charlie MacNeil, SASS #48580 Posted October 6, 2013 Author Share Posted October 6, 2013 Sorry I haven't replied before now, folks, got busy workin' cows and shootin' and otherwise sidetracked. Thanks for the info. It looks like I need to get a brass punch next time I go to town. Link to comment Share on other sites More sharing options...
Bullett Sass 19707 Posted October 6, 2013 Share Posted October 6, 2013 Hi Charlie, my newer 45lc you have to beat the h--l out of that forward pin to get it out. Use the method to support the bolt. Bullett Link to comment Share on other sites More sharing options...
Mad Dog Jack, SASS #77862 Posted October 6, 2013 Share Posted October 6, 2013 Since I had to make an order from VTI for some things I ordered a pin just in case. Mine that came with the gun is a very loose fit. The one that came would need a hammer to get it in. So in my experience it is the pin, not the hole, that varies in size. Just thought I would throw that out, in case anyone is considering changing the hole size. Link to comment Share on other sites More sharing options...
Charlie MacNeil, SASS #48580 Posted October 7, 2013 Author Share Posted October 7, 2013 Thanks again, y'all! Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.