Rio Brazos Kid Posted June 20, 2013 Share Posted June 20, 2013 I have a Marlin that doesn't like 38 length ammo, so I load 38 spl brass, setting the bullets out longer, which makes the Marlin very happy, So, since I load the rifle a tad hotter, along with a longer OAL, I use plated brass for the rifle, and brass brass for the pistols. Makes Identification easier, (actually more positive), and contrary to all I have heard, I NEVER have any problem with extraction of a split case, or for that matter any problems what-so-ever with the use of Nickle Brass in the rifle. I buy once fired range brass, both brass and nickle very cheap, so more frequent splitting of the nickle cases is of no real consequence in the long run. It runs thru the Marlin flawlessly, Is easier found by the brass shaggers, and is more easily identified by the shooter. I, like Buck D Law, find it works just fine, and it presents absolutely no problems for me. Link to comment Share on other sites More sharing options...
Madd Mike #8595 Posted June 20, 2013 Share Posted June 20, 2013 Has anybody actually done a study to determine if nickel platted brass splits faster than regular brass? I have operated on that assumption, but I haven't actually noticed any significant difference. Maybe my loading procedures are wrong, but most of my brass splitting occurs at the loading table. Only rarely does a case, nickel or brass, split on the line. I have noticed a huge difference, shooting a min of 10,000 rounds a year nickel reloads about 7 times max brass brass, agout 20 or more -+ mileage will vary Link to comment Share on other sites More sharing options...
Larsen E. Pettifogger, SASS #32933 Posted June 20, 2013 Share Posted June 20, 2013 I took a tour of an ammo plant a few years ago. This was a big plant where they actually made the brass they were loading. I specifically asked about nickle plated brass and whether it was more brittle than plain brass. They said nickle brass was primarily for situations where ammo is carried a long time and not used much. I.e., like many police officers. The nickle won't get verdigris or other damage like bare brass. They said the nickle plating process does embrittle the brass, but that for its intended purpose (one shot and throw it away) it was not a problem. Link to comment Share on other sites More sharing options...
Quick Draw Granpaw #48525 Posted June 20, 2013 Share Posted June 20, 2013 I've found that nickle plated brass will crack, maybe sooner than the brass cases. I only use the nickle plated brass in the pistol, NEVER IN THE RIFLE! i use the same load in both rifle & pistol so I just load em up then separate them accordingly. Happy trails QDG Link to comment Share on other sites More sharing options...
Southpaw Gringo, SASS # 74217 Posted June 20, 2013 Share Posted June 20, 2013 I bought some Starline nickel plated brass in .45 Colt about 5 years ago and I will tell you about half are still with me today and are getting reloaded regularly. There shot at least once a month in my rotation. They been loaded soo many times that theres barely any more nickel left on them. Just saying and of course. YMMV Link to comment Share on other sites More sharing options...
Dakota Brown Posted June 20, 2013 Share Posted June 20, 2013 I started with all brass 357s. As time went by, I accumulated some 38spl brass(usually happens when some pard brings your brass and dumps 'em in your brass bag). So on occasion, I would trade with a pard who has accumulated 357s in the same manner. And that's when I started using nickel casings. Unfortunately, I've had bad luck with them(the latest was shooting clean so far in an annual then #3 bullet case splits in your rifle and jams it! ), so I now use 'em exclusively on pistols. Link to comment Share on other sites More sharing options...
Cowboy Junky Posted June 20, 2013 Share Posted June 20, 2013 Because my pistol loads are different than my rifle loads........so it's easy to identify them. I use the nickel in the pistol because they split more. People will say all kinds of stuff about them being the same, different, harder, etc. I'm not in the brass business and I didn't even stay at a Holiday Inn Express but I can tell you this........for every split brass case I find I will find 3 or 4 split nickel. Link to comment Share on other sites More sharing options...
backshootin beauford mcgee Posted June 20, 2013 Share Posted June 20, 2013 shoot I just like the way it looks! Link to comment Share on other sites More sharing options...
Jabez Cowboy,SASS # 50129 Posted June 20, 2013 Share Posted June 20, 2013 Looks Great in the gun belt !!! Still use some in pistols , because I got it on the Cheap (free) .... Jabez Cowboy Link to comment Share on other sites More sharing options...
Turkey Creek Red, SASS # 22854 Posted June 20, 2013 Share Posted June 20, 2013 The experience that I have had with nickel vs regular brass is this. My wife shoots a Marlin, when I loaded regular brass and they would split, in the rifle, they would jam the rifle due to they way that they (normally) split. When we use nickel they tend (not always) to split differently and do not NORMALLY jam the rifle. As to whether they split sooner or not, I do not care, what I do care about is keeping the wife person happy. If that means using nickel vs brass, so be it. Link to comment Share on other sites More sharing options...
Buck D. Law, SASS #62183 Posted June 20, 2013 Share Posted June 20, 2013 It's important to remember that although brass will reload more times than nickel, it WILL eventually split. If a reloader's inspection process doesn't catch the split case BEFORE it gets reloaded and put in the rifle, it IS going to cause a problem when the bullet gets pushed into the case by the magazine spring. I use a nylon doo-rag (skull cap) to inspect my brass (actually Sugah does the brass inspection), but I've heard that ladies stockings work well. Either will find even the slightest beginning of a crack. Sometimes I have to get a magnifying glass to see what the doo-rag snags on. Link to comment Share on other sites More sharing options...
Fingers McGee Posted June 20, 2013 Share Posted June 20, 2013 I'm guessing that most of the nay-sayers on here are shooting .38/.357. or some other straight walled case with smokeless powder. I too have experienced numerous split cases using smokeless powder with nickel .38 specials of a variety of headstamps except Starline. I normally shoot blackpowder rounds in a .44-40 '66 carbine or '73 short rifle using Starline nickel cases without incident. I lose many more cases to the brass gods than I do to split case mouths. Bottom line IMNSHO is it depends on what powder, caliber, manufacturer's cases and loading procedures you are using that determines the frequency of split cases. Fingers (Show Me MO smoke) McGee Link to comment Share on other sites More sharing options...
Happy Jack, SASS #20451 Posted June 20, 2013 Share Posted June 20, 2013 I am also a member of the minority here. I use nickel cases exclusively for CAS matches. I have been using nickel cases for MANY years. While some are not too good others I have have been reloaded until the plating is almost worn off with no problems. I agree with Fingers, it depends a lot on your reloading procedures. As to my experience with nickel: Remington (R-P) CRAP !!! Winchester Not good Speer Holds up pretty well Federal Great Starline: Absolutely the best I only use new or once fired Starline at EOT, WR, or Regionals. Everywhere else I use Federal or Speer. I only use Winchester and R-P for practice. In all the years I have NEVER had a nickel case split and jam a rifle. Your experience may be different. Link to comment Share on other sites More sharing options...
Krazy Kajun Posted June 20, 2013 Share Posted June 20, 2013 But he rode around in the hard wild west. Wearing a powder blue jump suit. Might have been the real reason for the mask. Now AA...that's just wrong on some many levels! (gotta admit it's funny though) I once used nickel brass at a lost brass match and only used it in my pistols (dumba$$) and..and..and..I once reloaded some nickel brass sooooo many times it became penny brass [rimshot] I have noticed that nickel brass does seem to split more often than "brass" brass but, like someone posted earlier, I've seen the splits mostly along the side and not at the mouth of the nickel brass....I'm not sure why it fails that way more often though. Link to comment Share on other sites More sharing options...
Cpt Dan Blodgett, SASS #75655 Posted June 20, 2013 Share Posted June 20, 2013 I purchased 500 starline nickle plated brass to shoot out of my RNVs, my rifle and other match pistols are 44 mag. The nickle cases make 44 vs 45 separation a snap. Link to comment Share on other sites More sharing options...
Fingers McGee Posted June 20, 2013 Share Posted June 20, 2013 . As to my experience with nickel: Remington (R-P) CRAP !!! Winchester Not good Speer Holds up pretty well Federal Great Starline: Absolutely the best That's been pretty much my experience with the various makers also Fingers (Show Me MO smoke) McGee Link to comment Share on other sites More sharing options...
Checotah Posted June 20, 2013 Share Posted June 20, 2013 I started reloading in 2008, when I retired. Preparing for that, I had accumulated a couple thousand nickle and a couple thousand brass cases, all reloaded at least once (.38 spl). Also bought a thousand Starline brass, planning to eventually go to it once the used stuff wore out. Figured I'd use up the nickle first, since I had heard how it splits so easily/much. Am still using it. A lot of it has about half the nickle worn off but it's still usable. Have been seeing about 1 or 2% splits, although it's now getting up to about 5%. I inspect before lubing & putting into the hopper and again after loading, throwing away any with visible split. I think a lot of the splitting happens because of the flaring and sizing. I bell the case only minimally, just enough to hold the bullet and not shave lead. I also load to the upper half of the loading charts, FWIW. Don't want those nickle cases? Send 'em my way... Link to comment Share on other sites More sharing options...
Go West Posted June 21, 2013 Share Posted June 21, 2013 Nickel brass with a cannelure is not your friend in a rifle. There is a tendency to split off and remain in your chamber. Link to comment Share on other sites More sharing options...
Cowboy Rick, SASS #49739L Posted June 21, 2013 Share Posted June 21, 2013 I am also a member of the minority here. I use nickel cases exclusively for CAS matches. I have been using nickel cases for MANY years. While some are not too good others I have have been reloaded until the plating is almost worn off with no problems. I agree with Fingers, it depends a lot on your reloading procedures. As to my experience with nickel: Remington (R-P) CRAP !!! Winchester Not good Speer Holds up pretty well Federal Great Starline: Absolutely the best I only use new or once fired Starline at EOT, WR, or Regionals. Everywhere else I use Federal or Speer. I only use Winchester and R-P for practice. In all the years I have NEVER had a nickel case split and jam a rifle. Your experience may be different. Once burned, I guess - my first foray into new nickel brass was with RP. Never again. CR Link to comment Share on other sites More sharing options...
Billy Boots, # 20282 LTG-Regulator Posted June 21, 2013 Share Posted June 21, 2013 Agree with most said in thread. I like nickel for BP, brass for smokeless in order to keep separate. Since I do find nickel to crack more I inspect each match round that is for rifle, chamber gauge it, and mark it with red mark. Small cracked brass seems to be fine in revolvers. Link to comment Share on other sites More sharing options...
Cowboy Rick, SASS #49739L Posted June 21, 2013 Share Posted June 21, 2013 Agree with most said in thread. I like nickel for BP, brass for smokeless in order to keep separate. Since I do find nickel to crack more I inspect each match round that is for rifle, chamber gauge it, and mark it with red mark. Small cracked brass seems to be fine in revolvers. Revolvers are the only guns I am willing to risk using nickel plated. Soon it will be all gone and I'll be free of the temptation to keep using it! Dadgum this New England thriftiness blood anyway! Frugal? Not me, just can't pitch something that still has life in it CR Link to comment Share on other sites More sharing options...
Hurricane Deck 100366 Posted March 31, 2015 Share Posted March 31, 2015 I am in the process of culling all the nickel out of my 38 cases after having several split during practice. the quality seems to be all over the place with the plating. As has been stated, I have some that have been reloaded so many times that the nickel plating is wearing off! Others don't make it 5 reloads. I use them to set up the belling on the reloading press. I see to cringe less when I over-bell, crush or otherwise destroy a nickel case. Link to comment Share on other sites More sharing options...
Church Key, SASS # 33713 Posted March 31, 2015 Share Posted March 31, 2015 I use .38 nickel cases in my revolvers; care less if they split. Can tell them from my brass cases of which I only use Starline in my rifle, adding about 1K new ones a year. I trade the other brass headstamps for nickel. I also use nickel cases in .44 Russian and Mag. for BP matches; total two a year. The MD and PA BP championships. Link to comment Share on other sites More sharing options...
Most Wanted Posted April 1, 2015 Share Posted April 1, 2015 I use .38 nickel cases in my revolvers; care less if they split. Can tell them from my brass cases of which I only use Starline in my rifle, adding about 1K new ones a year. I trade the other brass headstamps for nickel. I also use nickel cases in .44 Russian and Mag. for BP matches; total two a year. The MD and PA BP championships. I used to use the nickel in my pistols and like you said no big deal if they split. But when the nickel wears off it gets hard to tell them apart. So last year I threw them all out. Not worth it in the long run. Link to comment Share on other sites More sharing options...
John Barleycorn, SASS #76982 Posted April 1, 2015 Share Posted April 1, 2015 I use nickel cases for my BP loads. Bdoc shoots smokeless and we only use brass for those so we can tell at a glance if it's smokeless or BP. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.