Korupt Karl Posted March 8, 2011 Share Posted March 8, 2011 Looking for the small screwdrivers that go in your cartridge belt. Made using a rifle cartridge with a screwdriver tip. Either looking for ready made or some input on where to get the screwdriver tips and/or how to make. Thanks KK Link to comment Share on other sites More sharing options...
Chas B. Wolfson, SASS #11104 Posted March 8, 2011 Share Posted March 8, 2011 Lefty Dude out here in sunny AZ. I believe they are marketed through UniqueTek.com Chas B. Link to comment Share on other sites More sharing options...
Lefty Wheeler Posted March 8, 2011 Share Posted March 8, 2011 Howdy: Lumber or hardware for the tip, you can get long shanked ones that are different sizes. You can epoxy it into the case and use a hex crimp tool that is used for crimping TV cable. Just test the size of the tool to the tip and add the brass to both sides (best guess). Once you have it assembled hold it tip down to let the epoxy settle into the tip and dry. Lefty Link to comment Share on other sites More sharing options...
Pit Bull Tex Posted March 8, 2011 Share Posted March 8, 2011 Unique Tek 's site dont works. Link to comment Share on other sites More sharing options...
Slowhand Bob, 24229 Posted March 8, 2011 Share Posted March 8, 2011 For better quality you could order the Brownells Mag-Tips in the specific sizes needed and order some of the stock bedding compound to set them into the case with. Another post would probably yield just the right size tips to order and case size appropriate for the job. Link to comment Share on other sites More sharing options...
JD Trampas, SASS # 55781 Posted March 8, 2011 Share Posted March 8, 2011 Redwing sells a knife with a screwdriver bit, have seen alot of them at shoots All for now JD Trampas Link to comment Share on other sites More sharing options...
Cypress Sam, SASS #10915 Posted March 8, 2011 Share Posted March 8, 2011 KK, You can get a very usable small screwdriver at most any auto parts store. Many times they are giveaways. They ain't pretty though. Won't match your shirts. Link to comment Share on other sites More sharing options...
Lefty Dude, SASS # 51223 Posted March 8, 2011 Share Posted March 8, 2011 Try Here; http://www.uniquetek.com Link to comment Share on other sites More sharing options...
August West, SASS #45079 Posted March 8, 2011 Share Posted March 8, 2011 Try Here; http://www.uniquetek.com Linky no worky Link to comment Share on other sites More sharing options...
Buck D. Law, SASS #62183 Posted March 8, 2011 Share Posted March 8, 2011 KK, if you go to the Missouri State match, lead your category until the 10th stage and then leave 7 in your rifle because you don't have one of those screwdrivers....there's a fellow there that will give you one. That's the rumor anyway. Link to comment Share on other sites More sharing options...
Lefty Dude, SASS # 51223 Posted March 8, 2011 Share Posted March 8, 2011 Site is working; http://www.uniquetek.com Link to comment Share on other sites More sharing options...
Lazarus Longshot, SASS #44254 Life Posted March 8, 2011 Share Posted March 8, 2011 Site is working; http://www.uniquetek.com Site works fine. I've got a couple of their screwdrivers. One uses Brownell's interchangeable bits and is built into a .45-70 case, the other is a fixed bit that fits in my .38 caliber loops. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.