Captain Action, SASS #70709 Posted December 21, 2010 Share Posted December 21, 2010 ...with a recently aquired, well-worn 1897 "E" model w/30" barrel manufactured in 1913. (I will not be cutting the barrel!) I'm putting together a parts list and need some advice with a problem. Once in every 20 or so cycles, the hammer follows the bolt forward. Worn sear?? Any help would be appreciated. Link to comment Share on other sites More sharing options...
Garrison Joe, SASS #60708 Posted December 21, 2010 Share Posted December 21, 2010 Perhaps, but could also be that the main spring is adjusted too light with the tension screw, or the main spring is weak. See if you can tighten the main spring tension screw a little. Could also be the main notch on the hammer cut too thin to hold reliably. Good luck, GJ Link to comment Share on other sites More sharing options...
Nate Kiowa Jones #6765 Posted December 21, 2010 Share Posted December 21, 2010 ...with a recently aquired, well-worn 1897 "E" model w/30" barrel manufactured in 1913. (I will not be cutting the barrel!) I'm putting together a parts list and need some advice with a problem. Once in every 20 or so cycles, the hammer follows the bolt forward. Worn sear?? Any help would be appreciated. If like you say it's well worn, most likely the bolt and frame rails are so worn the bolt is riding up as it comes back. Riding up so much that it won't push the hammer down enough to cock. If that is the problem a new sear will only make it worse. The action needs to be tightened up some. You have to grow or add some metal where needed to do this. Link to comment Share on other sites More sharing options...
Captain Action, SASS #70709 Posted December 22, 2010 Author Share Posted December 22, 2010 If like you say it's well worn, most likely the bolt and frame rails are so worn the bolt is riding up as it comes back. Riding up so much that it won't push the hammer down enough to cock. If that is the problem a new sear will only make it worse. The action needs to be tightened up some. You have to grow or add some metal where needed to do this. Link to comment Share on other sites More sharing options...
Captain Action, SASS #70709 Posted December 22, 2010 Author Share Posted December 22, 2010 As per GJ's advice, I tightened the mainspring tension screw. Helped a bit (1 in 50 odd cycles now), but Nate's correct unfortunately. The receiver rails and top of the hammer are worn. Believe I'll use it for an occasional BP bird hunt and get something else for CAS. Thanks for the help. (This is why I love The Wire!) Link to comment Share on other sites More sharing options...
Captain Long Story, US Cavalry Posted March 2, 2011 Share Posted March 2, 2011 If like you say it's well worn, most likely the bolt and frame rails are so worn the bolt is riding up as it comes back. Riding up so much that it won't push the hammer down enough to cock. If that is the problem a new sear will only make it worse. The action needs to be tightened up some. You have to grow or add some metal where needed to do this. Sounds like I have a similar problem - the amount of build-up is just .001s of an inch, is there anything I'd need to be mindful of after growing metal in those two tracks? Link to comment Share on other sites More sharing options...
Captain Woodrow Cahill, SASS # 54363 Posted March 2, 2011 Share Posted March 2, 2011 If like you say it's well worn, most likely the bolt and frame rails are so worn the bolt is riding up as it comes back. Riding up so much that it won't push the hammer down enough to cock. If that is the problem a new sear will only make it worse. The action needs to be tightened up some. You have to grow or add some metal where needed to do this. Howdy Nate - In reading this thread, it made me think of other guns with "slop" in the action. If I recall correctly there's a trick with the 1911 that involves squeezing down the slide to make it ride a bit tighter on the frame. Could the receiver on a 97 be pushed in a bit to take up the slack between the bolt and frame rails? Link to comment Share on other sites More sharing options...
Cowboy Junky Posted March 2, 2011 Share Posted March 2, 2011 Couldn't you build up the hammer....seems like that would be the easist fix. Link to comment Share on other sites More sharing options...
Marauder SASS #13056 Posted March 2, 2011 Share Posted March 2, 2011 Yes, you could build up the hammer a bit, but it would make the action a little harder to work and would make the gun wear even more. Some folks would "re-arbor" the frame to help. I've heard others used plating (such as nickle plating the gun) to help. Not sure how Nate was meaning to do it. Link to comment Share on other sites More sharing options...
Garrison Joe, SASS #60708 Posted March 2, 2011 Share Posted March 2, 2011 Not sure how Nate was meaning to do it. Could be a plasma metallizing shop down the street from Nate- using equipment and spray metal like this (commonly done on marine equipment rebuilds)? http://www.plasmapowders.com/ Good luck, GJ Link to comment Share on other sites More sharing options...
Captain Long Story, US Cavalry Posted March 3, 2011 Share Posted March 3, 2011 I've heard others used plating (such as nickle plating the gun) to help. I wonder if there's a way to wrap the exterior of the receiver, then dip it? Tape? Link to comment Share on other sites More sharing options...
seven, #15837 Posted March 3, 2011 Share Posted March 3, 2011 Shorten the sear to raise the hammer. Once cocked, keep the overtravel to a minimum. Link to comment Share on other sites More sharing options...
Ol Number4 Posted March 3, 2011 Share Posted March 3, 2011 Seven has the easiest fix. Shorten the sear bar on the hammer end. Ol' #4 Link to comment Share on other sites More sharing options...
Captain Long Story, US Cavalry Posted March 3, 2011 Share Posted March 3, 2011 Seven has the easiest fix. Shorten the sear bar on the hammer end. Ol' #4 Thanks - much better than welding and / or plating. Link to comment Share on other sites More sharing options...
Nate Kiowa Jones #6765 Posted March 3, 2011 Share Posted March 3, 2011 Shorten the sear to raise the hammer. Once cocked, keep the overtravel to a minimum. That's the quickest fix but you gotta be real careful. If you take too much the action gets really stiff because the hammer is now rubbing the bottom of the bolt all the time. Next option is to add a little metal to the bottom of the bolt there at the back end. Link to comment Share on other sites More sharing options...
Danite SASS #27034 Posted March 4, 2011 Share Posted March 4, 2011 I replaced the hammer and solved a 5 out of every 6 problem. Shot fast but dangerously. Link to comment Share on other sites More sharing options...
Captain Long Story, US Cavalry Posted March 7, 2011 Share Posted March 7, 2011 I replaced the hammer and solved a 5 out of every 6 problem. Shot fast but dangerously. Same here, as well as tweaking the trigger spring and retaining screw. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.