-
Posts
402 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Everything posted by Sam Sackett
-
I believe my comprehension is just fine. Everybody isn’t the same. We all hear or read the same thing, but some end up understanding the stage differently. Case in point, we are now having a long discussion about this particular stage. No real need to get snarky…….. Have a Blessed day…. Sam Sackett
-
Might want to check the chamber. Could be something in there not letting another one in? I have older Rossi’s and I don’t believe there is and type of trigger block or safety on them. Never tried, but they would probably release the hammer whenever you pulled the trigger, even before the bolt was fully closed. Never tried it. Don’t know about the newer ones. Sam Sackett
-
I would have shot it this way. 3,2,1,2,3 with first pistol. 3,4,5,4,3 with second pistol. Instructions could have been interpreted that way. Start and finish on 3 .. with each pistol……. Poorly written instructions….. Sam Sackett
-
Good luck. Sam Sackett
-
This thread is about slip hammering. Could it be that holding the trigger back during slip hammering will allow the cylinder to over rotate? I’m thinking not, but could the cylinder stop (bolt) stay down enough to allow it? I dunno. Never tried it and probably won’t. Sam Sackett
-
WTS some preset dies for Lee Classic Turret
Sam Sackett replied to Wild Hair Larry's topic in SASS Wire Classifieds
Looks like the decapping rods are not installed in the dies. Are they included? Is the fourth die in each set a Lee crimp die? Sam Sackett -
Shotgun chaps are fairly tight fitting on the legs and have a zipper down the leg. Are they much different than the chaps motorcycle riders use? They seem about the same to me. Maybe I’m way off base though…. Sam Sackett
-
Maybe not, but it’s a job that can put groceries on the table. I will NOT use a self checkout. Even if the “Assistant” offers to check me out on one, I will decline. The “self” checkout still gets the credit for the sale and that’s what goes on the reports. I do not believe that self checkouts are saving money for the businesses in the long run. There are many reports that show that many are sneaking items through and not paying for them. That is store loss and cost. I don’t think I am alone. I have left a cartful of items and walked out if there was no cashier. And I’ll do it again.. Sam Sackett
-
It’s not a 73, but I have. 1997 model Marlin 1894 Limited JM stamp in. 45 Colt a 24” barrel if that might fit your desires….. pretty nice shape. PM if interested… Sam Sackett
-
If you like the army grip better this may work for you
Sam Sackett replied to Buckshot Bob 's topic in SASS Wire
Nice! But with those I won’t have to tuck my little finger under the grip. Might be worth a try…… Sam Sackett -
I’ve seen both High Beam and Low Beam…….. Sam Sackett
-
Dick Dastardly……..
-
I ran out of Clays and found a 4 lb jug of Titewad. I load 12 ga AA or STS with about 14 gr, CB0175 wad and 3/4oz of shot. Works great and light recoil. Sorry, but I’m not close to the reloading bench and don’t have the exact formula, but as you can see I’m in the ballpark with the rest. Sam Sackett
-
Browning M1892 Centenial For Sale
Sam Sackett replied to J.C. Bell, SASS #15217's topic in SASS Wire Classifieds
Aaaahh. Missed that. Was hoping it was a 45 Colt Sam Sackett -
Browning M1892 Centenial For Sale
Sam Sackett replied to J.C. Bell, SASS #15217's topic in SASS Wire Classifieds
Maybe I missed it, but I’m not seeing the caliber listed…….. Sam Sackett -
Nonalcoholic drink(s)
Sam Sackett replied to Marshal Mo Hare, SASS #45984's topic in SASS Wire Saloon
Nonalchoholic? Blasphemy! what next? Vegan? Ha!, Ha! Sam Sackett -
WTB Replacement Stock for Stoeger Coach Gun, 12 Ga
Sam Sackett replied to "HH" (a.k.a. Dave)'s topic in SASS Wire Classifieds
You might be able to locate a cabinet maker / woodworker that could cut the bad area out and fit in a replacement section. If done correctly it would be as strong as original and not be very noticeable. Sam Sackett -
Looking For - WTB - Stoeger Coach Gun Lock Impeller
Sam Sackett replied to Mossy Horn Gent's topic in SASS Wire Classifieds
Great news, Johnny! Sam Sackett -
Looking For - WTB - Stoeger Coach Gun Lock Impeller
Sam Sackett replied to Mossy Horn Gent's topic in SASS Wire Classifieds
I used a number 12 double headed construction nail. Grind the first head back to the approx shape of the original and cut to length. It’s been working for over 3 years now. Put my original pin in the spare parts box in case I ever needed it. Sam Sackett -
NEEDED> 2 Screws For A Winchester Model 94
Sam Sackett replied to joachim slim's topic in SASS Wire Classifieds
These are commonly available from our normal suppliers. https://www.midwayusa.com/product/1100527601 Sam Sackett -
Yep! It’s the very calm, peace loving, tolerant individual. Or maybe not. Sam Sackett
-
Looking at the pictures, it looks like the shells fit deep in the pockets. This isn’t good, as it makes them harder to pull quickly. If you go with this belt, you might want to put a filler in the bottom of the pockets so the shells ride higher. Makes them a lot easier to grab. I think this would be a good belt for hunting, but maybe not so good for our game. Just my two Pennie’s worth…… Sam Sackett
-
Bobby Tyler TALO Ruger Vaquero - Gunfighter Grips?
Sam Sackett replied to Buckshot Bear's topic in SASS Wire
Uhhhhh. Don’t know, but I like ‘em! Sam Sackett